Drone flight controller
Adan-Khalid·drone-flight-controller·hardware/kicad/mcu.kicad_sch
About the Drone flight controller PCB
Drone flight controller is an open source STM32 PCB design by Adan-Khalid, published on GitHub under the Custom license license. It is a board, with 20 components from 11 distinct parts.
Its main chip is the STM32H743VIT6TR, from the STM32 family. By type, the board carries 13 capacitors, 3 resistors, 2 diodes, 1 IC and 1 crystal.
It belongs with the robotics & motion designs in this gallery.
From the project
ArduPilot flight controller for a quadcopter: STM32H743, two IMUs, barometer, microSD. KiCad 10 schematic with ERC, netlist and ArduPilot DMA checks.
scripts/kicadchecks.sh` runs KiCad's electrical rules check (ERC) on every push, and the design rules check (DRC) once a board file is committed.
Board layout status: not finished. buildboard.py places the parts on a 36 x 36 mm, 4-layer board (the placement renders in the main README come from it), but routing with routeboard.py and Freerouting left connections open and cut into the ground layer, so the board file is not committed. The routing scripts stay here as a record of what was tried (docs/LEARNING.md, section 13).
Main components on the Drone flight controller
Drone flight controller bill of materials (BOM)
20 components, 11 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | STM32H743VIT6TR STM32H743VIT6 | LQFP-100_14x14mm_P0.5mm | U7 |
| 1 | TAXM8M4RFDCET2T 8MHz | Crystal_SMD_3225-4Pin_3.2x2.5mm | Y1 |
| 1 | KT-0603R red | LED_0603_1608Metric | D2 |
| 1 | KT-0603W white | LED_0603_1608Metric | D3 |
| 7 | 100NF 100nF | C_0402_1005Metric | C21, C22, C23, C24, C25, C28, C31 |
| 1 | 10UF 10uF | C_0805_2012Metric | C26 |
| 1 | 1UF 1uF | C_0402_1005Metric | C27 |
| 2 | 2.2UF 2.2uF | C_0603_1608Metric | C29, C30 |
| 2 | 15PF 15pF | C_0402_1005Metric | C32, C33 |
| 1 | 10K 10k | R_0402_1005Metric | R12 |
| 2 | 1k | R_0402_1005Metric | R13, R14 |
Drone flight controller design files
The KiCad project lives in the Adan-Khalid/drone-flight-controller repository on GitHub; these links point at the commit this page was built from.
Drone flight controller: common questions
What microcontroller does the Drone flight controller use?
The Drone flight controller is built around the STM32H743VIT6TR, from the STM32 family.
How many components are on the Drone flight controller?
20 components, from 11 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Drone flight controller design files?
From the Adan-Khalid/drone-flight-controller repository on GitHub, which has the schematic and the BOM; the links under Design files point to each one.
Can I use the Drone flight controller design in my own project?
It is published under Custom license, which limits how it may be reused; read the license before building on it.
Can I test firmware for the Drone flight controller without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.
Similar boards
STM32
LumenPnP Motherboard
opulo-inc
149 × 95 mm296 parts4LCC-BY-SA-4.03.7kSTM32
Type g
google
169 × 30 mm24 parts2LApache-2.02.9kSTM32
Main panel
google
234 × 84 mm26 parts4LApache-2.02.9kSTM32
Base
google
52.3 × 52.3 mm36 parts2LApache-2.02.9kSTM32
Type a
google
150 × 30 mm14 parts2LApache-2.02.9kSTM32
Type c
google
188 × 30 mm17 parts2LApache-2.02.9k