ProjectObelisk
bnigg17·ProjectObelisk·PCB/CameraAI_PCB.kicad_pcb
About the ProjectObelisk PCB
ProjectObelisk is an open source STM32 PCB design by bnigg17, published on GitHub. It is a 2-layer board measuring 106 × 55.5 mm, with 38 components from 16 distinct parts.
Its main chip is the STM32H7A3ZITxQ, from the STM32 family. By type, the board carries 24 capacitors, 8 connectors, 3 resistors, 2 switches and 1 IC.
Main components on the ProjectObelisk
ProjectObelisk bill of materials (BOM)
38 components, 16 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | STM32H7A3ZITxQ | LQFP-144_20x20mm_P0.5mm | U1 |
| 1 | OV7670_CONNECTOR | PinHeader_2x09_P2.54mm_Horizontal | J1 |
| 1 | USB_A | USB3_A_Molex_48393-001 | J2 |
| 1 | ST_LINK_CONNECTOR | PinHeader_1x07_P2.54mm_Vertical | J3 |
| 1 | SD_CARD_CONN | PinHeader_1x06_P2.54mm_Vertical | J4 |
| 1 | Conn_01x02_Pin | PinHeader_1x02_P2.54mm_Vertical | J5 |
| 1 | UART | PinHeader_1x04_P2.54mm_Vertical | J6 |
| 1 | Conn_01x03_Pin | PinHeader_1x03_P2.54mm_Vertical | J7 |
| 1 | Conn_01x08_Pin | PinHeader_1x08_P2.54mm_Vertical | J8 |
| 2 | SW_Push | Nidec_Copal_SH-7010A | SW1, SW2 |
| 19 | 100nF | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C1, C4, C5, C6, C7, C8, C9, C10 +11 |
| 1 | 4.7uF | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C2 |
| 1 | 1uF | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C3 |
| 3 | 2.2uF | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C22, C23, C24 |
| 2 | 10k | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1, R3 |
| 1 | 47 | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R2 |
ProjectObelisk design files
The KiCad project lives in the bnigg17/ProjectObelisk repository on GitHub; these links point at the commit this page was built from.
- LayoutPCB/CameraAI_PCB.kicad_pcb
- SchematicPCB/CameraAI_PCB.kicad_sch
ProjectObelisk: common questions
What microcontroller does the ProjectObelisk use?
The ProjectObelisk is built around the STM32H7A3ZITxQ, from the STM32 family.
How big is the ProjectObelisk PCB?
The ProjectObelisk measures 106 × 55.5 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the ProjectObelisk?
38 components, from 16 distinct parts. The full bill of materials is listed on this page.
Where can I download the ProjectObelisk design files?
From the bnigg17/ProjectObelisk repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the ProjectObelisk design in my own project?
The repository has no license, so all rights stay with bnigg17. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the ProjectObelisk without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.
Similar boards
STM32
LumenPnP Motherboard
opulo-inc
149 × 95 mm296 parts4LCC-BY-SA-4.03.7kSTM32
Type g
google
169 × 30 mm24 parts2LApache-2.02.9kSTM32
Main panel
google
234 × 84 mm26 parts4LApache-2.02.9kSTM32
Base
google
52.3 × 52.3 mm36 parts2LApache-2.02.9kSTM32
Type a
google
150 × 30 mm14 parts2LApache-2.02.9kSTM32
Type c
google
188 × 30 mm17 parts2LApache-2.02.9k