Duplexer 145 435 BNC 25W REV A

Brico-Hams·antenaSatCommrotor·PortableSatLite/hardware/diplexer/Duplexer_145_435_BNC_25W_REV_A/Duplexer_145_435_BNC_25W_REV_A.kicad_pcb

Duplexer 145 435 BNC 25W REV A PCB layout, top view — open source board by Brico-Hams

About the Duplexer 145 435 BNC 25W REV A PCB

Duplexer 145 435 BNC 25W REV A is an open source PCB design by Brico-Hams, published on GitHub. It is a 2-layer board measuring 80 × 60 mm, with 13 components from 13 distinct parts.

By type, the board carries 5 inductors, 5 capacitors and 3 connectors.

From the project

DUPLEXER 145 / 435 MHz — BNC — 25 W TARGET — REV A

DUPLEXER 145 / 435 MHz — BNC — 25 W TARGET — REV A

Architecture J1 ANT -> 5th-order Chebyshev LPF -> J2 VHF J1 ANT -> 5th-order Chebyshev HPF -> J3 UHF

Filter values are based on the published KI0AG 2m/70cm micro-duplexer: LPF: 68 nH, 18 pF, 100 nH, 18 pF, 68 nH HPF: 4.7 pF, 16 nH, 3.1 pF, 16 nH, 4.7 pF

Target bands: VHF: 144–146 MHz, nominal 145 MHz UHF: 430–440 MHz, nominal 435 MHz System impedance: 50 ohm Power target: 25 W

Duplexer 145 435 BNC 25W REV A bill of materials (BOM)

13 components, 13 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
BNC ANT 50R
J1
1
BNC VHF 50R
J2
1
BNC UHF 50R
J3
1
68nH
L1
1
100nH
L2
1
68nH
L3
1
16nH
L4
1
16nH
L5
1
18pF
C1
1
18pF
C2
1
4.7pF
C3
1
3.1pF
C4
1
4.7pF
C5

Duplexer 145 435 BNC 25W REV A design files

The KiCad project lives in the Brico-Hams/antenaSatCommrotor repository on GitHub; these links point at the commit this page was built from.

Duplexer 145 435 BNC 25W REV A: common questions

How big is the Duplexer 145 435 BNC 25W REV A PCB?

The Duplexer 145 435 BNC 25W REV A measures 80 × 60 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Duplexer 145 435 BNC 25W REV A?

13 components, from 13 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the Duplexer 145 435 BNC 25W REV A design files?

From the Brico-Hams/antenaSatCommrotor repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the Duplexer 145 435 BNC 25W REV A design in my own project?

The repository has no license, so all rights stay with Brico-Hams. Use it as a reference, and ask the author before reusing the design.

More boards in antenaSatCommrotor