IrTool
charles-works·irTool·hardware/kicad/remote.kicad_pcb
About the IrTool PCB
IrTool is an open source STM32 PCB design by charles-works, published on GitHub. It is a 2-layer board measuring 170 × 75 mm, with 17 components from 17 distinct parts.
Its main chip is the STM8L051F3P6, from the STM32 family. By type, the board carries 5 test points, 3 switches, 3 capacitors, 2 resistors, 1 IC and 1 transistor.
From the project
IR Remote DIY
Complete KiCad schematic and PCB for the STM8L051F3P6 + IRLML2502 + CR2032 NEC IR remote.
Main components on the IrTool
IrTool bill of materials (BOM)
17 components, 17 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | STM8L051F3P6 | U1_STM8L051F3P6_TSSOP20 | U1 |
| 1 | IRLML2502 | Q1_IRLML2502_SOT23 | Q1 |
| 1 | CR2032 | BT1_CR2032_Holder | BT1 |
| 1 | KEY1 | SW1_KEY1 | SW1 |
| 1 | KEY2 | SW2_KEY2 | SW2 |
| 1 | KEY3 | SW3_KEY3 | SW3 |
| 1 | SWIM | TP1_SWIM | TP1 |
| 1 | NRST | TP2_NRST | TP2 |
| 1 | VDD | TP3_VDD | TP3 |
| 1 | GND | TP4_GND | TP4 |
| 1 | DBG | TP5_DBG | TP5 |
| 1 | 940nm | D1_IR_LED_5mm | D1 |
| 1 | 100nF | C1_100nF_0402 | C1 |
| 1 | 4.7uF | C2_4u7F_0603 | C2 |
| 1 | 47uF OPT | C3_47uF_OPT | C3 |
| 1 | 10-22R | R1_IR_LED_0603 | R1 |
| 1 | 100R | R2_GATE_100R_0603 | R2 |
IrTool design files
The KiCad project lives in the charles-works/irTool repository on GitHub; these links point at the commit this page was built from.
IrTool: common questions
What microcontroller does the IrTool use?
The IrTool is built around the STM8L051F3P6, from the STM32 family.
How big is the IrTool PCB?
The IrTool measures 170 × 75 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the IrTool?
17 components, from 17 distinct parts. The full bill of materials is listed on this page.
Where can I download the IrTool design files?
From the charles-works/irTool repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the IrTool design in my own project?
The repository has no license, so all rights stay with charles-works. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the IrTool without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.
Similar boards
STM32
LumenPnP Motherboard
opulo-inc
149 × 95 mm296 parts4LCC-BY-SA-4.03.7kSTM32
Type g
google
169 × 30 mm24 parts2LApache-2.02.9kSTM32
Main panel
google
234 × 84 mm26 parts4LApache-2.02.9kSTM32
Base
google
52.3 × 52.3 mm36 parts2LApache-2.02.9kSTM32
Type a
google
150 × 30 mm14 parts2LApache-2.02.9kSTM32
Type c
google
188 × 30 mm17 parts2LApache-2.02.9k