Locatof hw
dan-stefanov·locatof-hw·boards/uwb-beacon/pcb/rev-a/uwb-beacon.kicad_pcb
About the Locatof hw PCB
Locatof hw is an open source STM32 PCB design by dan-stefanov, published on GitHub under the CERN-OHL-P-2.0 license. It is a 4-layer board measuring 36 × 65 mm, with 89 components from 38 distinct parts.
Its main chip is the C5270980, from the STM32 family. Other key parts include the C2935406, C1850418, C171681, C2927042 and C435848. By type, the board carries 31 capacitors, 22 resistors, 13 ICs, 13 diodes, 3 transistors and 2 connectors.
It belongs with the power & battery, sensors and rf & radio designs in this gallery.
From the project
Open-source localization project based on UWB Time-of-Flight ranging
This scheme has one caveat: when VDD is below 1 V, the controller datasheet requires VDDUSB to remain below VDD + 300 mV. To satisfy this requirement, VDDUSB is enabled when VDDUSB_EN is pulled low. When VDD is below 1 V, BOR (brownout reset) keeps the controller pins in a high-Z state. During normal operation, VDD is above 1 V, and firmware may pull the pin low to enable USB communication. When using the STM32 bootloader, the user may close JP1 to bypass this logic.
Main components on the Locatof hw
Locatof hw bill of materials (BOM)
89 components, 38 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 3 | C2935406 RT9078-18GQZ | Richtek_ZQFN-4L | U1, U3, U5 |
| 1 | C5270980 STM32U575RGT6 | LQFP-64_10x10mm_P0.5mm | U2 |
| 1 | C1850418 ICM-42688-P | LGA-14_3x2.5mm_P0.5mm_LayoutBorder3x4y | U4 |
| 1 | C171681 BMM150 | WLCSP-12_1.56x1.56mm_P0.4mm | U6 |
| 1 | C2927042 GD5F1GQ5REYIGR | WSON-8-1EP_8x6mm_P1.27mm_EP3.4x4.3mm | U7 |
| 2 | C435848 USBLC6-4SC6Y | SOT-23-6 | U8, U12 |
| 1 | C2891574 AW21024QNR | QFN-32_1EP_4x4_Pitch0.4mm_EP2.9x2.9mm_ThermalVias | U9 |
| 2 | C89347 TPS70933DBVR | SOT-23-5 | U10, U13 |
| 1 | C81080 BQ24040DSQ | Texas_DSQ0010A_WSON-10-1EP_2x2mm_P0.4mm_EP0.9x1.5mm_ThermalVias | U11 |
| 1 | C28646264 HL6042 | SOT-23 | Q1 |
| 1 | C8512 MMBT2222A | SOT-23 | Q2 |
| 1 | C8492 LBSS84LT1G | SOT-23 | Q3 |
| 1 | C32346 Q13FC13500004 | Crystal_SMD_3215-2Pin_3.2x1.5mm | Y1 |
| 1 | C2982528 TYPEC-318A-ARP16X7SC16 | USB_C_Receptacle_XUNPU_TYPEC-318A-ARP16X7SC16 | J2 |
| 1 | C160403 SM03B-SRSS-TB | JST_SH_SM03B-SRSS-TB_1x03-1MP_P1.00mm_Horizontal | J3 |
| 1 | ~ | LiPo-303450_cut | BT1 |
| 1 | C5299931 DWM3000 | DWM3000 | DWM1 |
| 1 | C318887 TS-1187A-C-E-B | SW_XKB_TS-1187A | SW1 |
| 4 | C20617921 H5VUD5U | D_SOD-523 | D1, D2, D12, D13 |
| 8 | C5179615 A-SP1103R6GHB1W-C01-2C | LED_RGB_Amicc_A-SP1103R6GHB1W-C01-2C_Horizontal | D3, D4, D5, D6, D7, D8, D9, D10 |
Show 18 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | C19077514 SMF24A | D_SOD-123 | D11 |
| 1 | C1002 GZ1608D601TF | L_0603_1608Metric | FB1 |
| 12 | C307331 100nF | C_0402_1005Metric | C1, C3, C5, C7, C10, C11, C18, C21 +4 |
| 10 | C52923 1uF | C_0402_1005Metric | C2, C6, C9, C12, C14, C25, C26, C27 +2 |
| 1 | C23733 4.7uF | C_0402_1005Metric | C4 |
| 3 | C15525 10uF | C_0402_1005Metric | C8, C13, C17 |
| 2 | C1548 15pF | C_0402_1005Metric | C15, C16 |
| 1 | C15195 10nF | C_0402_1005Metric | C19 |
| 2 | C12530 2.2uF | C_0402_1005Metric | C29, C33 |
| 5 | C25744 10k | R_0402_1005Metric | R1, R11, R12, R14, R18 |
| 1 | C11702 1k | R_0402_1005Metric | R2 |
| 4 | C26083 1M | R_0402_1005Metric | R3, R6, R7, R8 |
| 2 | C25900 4.7k | R_0402_1005Metric | R4, R5 |
| 1 | C25792 47k | R_0402_1005Metric | R9 |
| 1 | C25768 22k | R_0402_1005Metric | R10 |
| 4 | C51721 3.9k | R_0402_1005Metric | R13, R17, R19, R21 |
| 2 | C25879 2.2k | R_0402_1005Metric | R15, R16 |
| 2 | C25862 1.2k | R_0402_1005Metric | R20, R22 |
Locatof hw design files
The KiCad project lives in the dan-stefanov/locatof-hw repository on GitHub; these links point at the commit this page was built from.
Locatof hw: common questions
What microcontroller does the Locatof hw use?
The Locatof hw is built around the C5270980, from the STM32 family.
How big is the Locatof hw PCB?
The Locatof hw measures 36 × 65 mm, has 4 copper layers and is 1.6062 mm thick.
How many components are on the Locatof hw?
89 components, from 38 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Locatof hw design files?
From the dan-stefanov/locatof-hw repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Locatof hw design in my own project?
Yes, under the terms of its CERN-OHL-P-2.0 license, which dan-stefanov chose for the repository.
Can I test firmware for the Locatof hw without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.
Similar boards
STM32
LumenPnP Motherboard
opulo-inc
149 × 95 mm296 parts4LCC-BY-SA-4.03.7kSTM32
Type g
google
169 × 30 mm24 parts2LApache-2.02.9kSTM32
Base
google
52.3 × 52.3 mm36 parts2LApache-2.02.9kSTM32
Main panel
google
234 × 84 mm26 parts4LApache-2.02.9kSTM32
Type a
google
150 × 30 mm14 parts2LApache-2.02.9kSTM32
Type c
google
188 × 30 mm17 parts2LApache-2.02.9k