Bldc controller-60v
darshp848·bldc-controller-60v·hardware/better-md80.kicad_pcb
About the Bldc controller-60v PCB
Bldc controller-60v is an open source STM32 PCB design by darshp848, published on GitHub. It is a 6-layer board measuring 56.7 × 54.7 mm, with 142 components from 62 distinct parts.
Its main chip is the ST STM32G474CEU6, from the STM32 family. Other key parts include the TI LM5164DDAR, TI TPS62163DSGR, TI TLV75533PDBVR, TI DRV8353SRTAR and TI TCAN1044AVDR. By type, the board carries 72 capacitors, 36 resistors, 8 ICs, 8 connectors, 6 transistors and 4 diodes.
It belongs with the robotics & motion designs in this gallery.
From the project
60 V, 20 A / 80 A peak BLDC motor controller that fits the MD80 v3.0 mounting. KiCad 10, 6 layers.
A 48 V nominal / 60 V max BLDC motor controller that fits wherever a MAB Robotics MD80 v3.0 fits: same outline, mounting holes, Micro-Fit and AUX connectors, phase-wire holes and encoder position, with the MD80's 20 A continuous / 80 A peak phase current.
This rebuilds footprints, schematic, netlist, ERC/DRC reports, BOM, the schematic PDF and the 3D renders. It leaves the routed PCB alone unless you run it with REGENPCB=1`, which regenerates the placement and throws the routing away (see tools/route.md to redo it). Schematic changes reach the board through KiCad's Update PCB from Schematic…

Main components on the Bldc controller-60v
Bldc controller-60v bill of materials (BOM)
142 components, 62 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | TI LM5164DDAR LM5164DDAR | Texas_HSOP-8-1EP_3.9x4.9mm_P1.27mm | U1 |
| 1 | TI TPS62163DSGR TPS62163DSGR | Texas_DSG0008A_WSON-8-1EP_2x2mm_P0.5mm_EP0.9x1.6mm | U2 |
| 1 | TI TLV75533PDBVR TLV75533PDBVR | SOT-23-5 | U3 |
| 1 | TI DRV8353SRTAR DRV8353SRTAR | Texas_RHA0040B_VQFN-40-1EP_6x6mm_P0.5mm_EP4.15x4.15mm | U4 |
| 1 | ST STM32G474CEU6 STM32G474CEU6 | QFN-48-1EP_7x7mm_P0.5mm_EP5.6x5.6mm | U5 |
| 1 | TI TCAN1044AVDR TCAN1044AVDR | SOIC-8_3.9x4.9mm_P1.27mm | U6 |
| 1 | ams OSRAM AS5047P-ATSM AS5047P-ATSM | TSSOP-14_4.4x5mm_P0.65mm | U7 |
| 1 | Analog MAX3490EESA+ MAX3490EESA+ | SOIC-8_3.9x4.9mm_P1.27mm | U8 |
| 6 | Infineon ISC022N10NM6ATMA1 ISC022N10NM6 | TDSON-8-1 | Q1, Q2, Q3, Q4, Q5, Q6 |
| 1 | Abracon ABM8-8.000MHZ-B2-T (verify CL) 8MHz | Crystal_SMD_3225-4Pin_3.2x2.5mm | Y1 |
| 2 | Molex 43045-0600 (R/A, 2x3) Micro-Fit 2x3 | MD80_MicroFit_2x03_RA | J1, J2 |
| 1 | Molex 53048-0650 AUX1 SPI enc | Molex_PicoBlade_53048-0610_1x06_P1.25mm_Horizontal | J3 |
| 1 | Molex 53048-0850 AUX2 RS422 | Molex_PicoBlade_53048-0810_1x08_P1.25mm_Horizontal | J4 |
| 1 | Motor NTC | MD80_NTC_Pads | J5 |
| 1 | Phase A | MD80_Phase_Pad | J10 |
| 1 | Phase B | MD80_Phase_Pad | J11 |
| 1 | Phase C | MD80_Phase_Pad | J12 |
| 1 | IXYS CPC1017NTR CPC1017N | SOP-4_3.8x4.1mm_P2.54mm | K1 |
| 2 | Vishay WSK2512 0.5 mOhm 1% (verify) 0.5m | R_Shunt_Vishay_WSK2512_6332Metric_T2.66mm | RS1, RS3 |
| 1 | Murata NCP18XH103F03RB 10k NTC | R_0603_1608Metric | TH1 |
Show 42 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | Littelfuse 5.0SMDJ60A 5.0SMDJ60A | D_SMC | D1 |
| 1 | Kingbright APTD1608LZGCK Green | LED_0603_1608Metric | D60 |
| 1 | Kingbright APTD1608LSURCK Red | LED_0603_1608Metric | D61 |
| 1 | Nexperia PESD2CAN,215 PESD2CAN | SOT-23 | D70 |
| 1 | Murata BLM18PG221SN1D BLM18PG221 | L_0603_1608Metric | FB1 |
| 1 | Bourns SRN4018-470M (verify Isat) 47u | L_Bourns-SRN4018 | L1 |
| 1 | Murata DFE252012F-2R2M 2.2u | L_1008_2520Metric | L2 |
| 1 | 10n | C_0402_1005Metric | C4 |
| 25 | TDK C3216X7S2A225K160AB 2.2u 100V | C_1206_3216Metric | C5, C100, C101, C102, C103, C104, C105, C106 +17 |
| 5 | Murata GRM188R72A104KA35D 100n 100V | C_0603_1608Metric | C6, C22, C26, C30, C42 |
| 1 | 2.2n | C_0402_1005Metric | C7 |
| 1 | 3.3n | C_0402_1005Metric | C8 |
| 1 | 56p | C_0402_1005Metric | C9 |
| 1 | Taiyo Yuden TMK325B7226KMHT 22u 25V | C_1210_3225Metric | C10 |
| 3 | 1u 25V | C_0603_1608Metric | C11, C44, C45 |
| 2 | 10u 25V | C_0805_2012Metric | C12, C40 |
| 1 | 22u 10V | C_0805_2012Metric | C13 |
| 5 | 1u | C_0402_1005Metric | C14, C16, C46, C65, C73 |
| 1 | 2.2u | C_0603_1608Metric | C15 |
| 14 | 100n | C_0402_1005Metric | C17, C32, C47, C60, C61, C62, C63, C66 +6 |
| 3 | 2.2n 100V | C_0603_1608Metric | C23, C27, C31 |
| 1 | 100n 25V | C_0402_1005Metric | C41 |
| 1 | Murata GRM188R72A473KA01D (verify) 47n 100V | C_0603_1608Metric | C43 |
| 3 | 470p | C_0402_1005Metric | C48, C49, C50 |
| 1 | 4.7u | C_0603_1608Metric | C64 |
| 2 | 10p | C_0402_1005Metric | C68, C69 |
| 2 | 100k | R_0603_1608Metric | R1, R3 |
| 1 | 5.1k | R_0402_1005Metric | R2 |
| 1 | 16.2k | R_0402_1005Metric | R4 |
| 1 | 75k | R_0402_1005Metric | R5 |
| 1 | 453k | R_0402_1005Metric | R6 |
| 1 | 49.9k | R_0402_1005Metric | R7 |
| 1 | 453k | R_0603_1608Metric | R8 |
| 7 | 0 | R_0402_1005Metric | R20, R21, R22, R23, R24, R25, R81 |
| 3 | 2.2 | R_1206_3216Metric | R30, R31, R32 |
| 5 | 10k | R_0402_1005Metric | R33, R40, R41, R60, R79 |
| 1 | 100k | R_0402_1005Metric | R42 |
| 3 | 1k | R_0402_1005Metric | R61, R62, R80 |
| 1 | 680 | R_0402_1005Metric | R70 |
| 2 | 120 | R_0603_1608Metric | R71, R76 |
| 4 | 33 | R_0402_1005Metric | R72, R73, R74, R75 |
| 2 | 100 | R_0402_1005Metric | R77, R78 |
Bldc controller-60v design files
The KiCad project lives in the darshp848/bldc-controller-60v repository on GitHub; these links point at the commit this page was built from.
- Layouthardware/better-md80.kicad_pcb
- Schematichardware/better-md80.kicad_sch
Bldc controller-60v: common questions
What microcontroller does the Bldc controller-60v use?
The Bldc controller-60v is built around the ST STM32G474CEU6, from the STM32 family.
How big is the Bldc controller-60v PCB?
The Bldc controller-60v measures 56.7 × 54.7 mm, has 6 copper layers and is 1.6 mm thick.
How many components are on the Bldc controller-60v?
142 components, from 62 distinct parts. The full bill of materials is listed on this page.
Where can I download the Bldc controller-60v design files?
From the darshp848/bldc-controller-60v repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Bldc controller-60v design in my own project?
The repository has no license, so all rights stay with darshp848. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Bldc controller-60v without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.
Similar boards
STM32
LumenPnP Motherboard
opulo-inc
149 × 95 mm296 parts4LCC-BY-SA-4.03.7kSTM32
Type g
google
169 × 30 mm24 parts2LApache-2.02.9kSTM32
Main panel
google
234 × 84 mm26 parts4LApache-2.02.9kSTM32
Base
google
52.3 × 52.3 mm36 parts2LApache-2.02.9kSTM32
Type a
google
150 × 30 mm14 parts2LApache-2.02.9kSTM32
Type c
google
188 × 30 mm17 parts2LApache-2.02.9k