STM32-Based Programmable Waveform Generator

devjamescollier·STM32-Based_Programmable_Waveform_Generator·Hardware/KiCad_Files/STM32-Based_Programmable_Waveform_Generator.kicad_pcb

STM32-Based Programmable Waveform Generator PCB layout, top view — open source STM32 board by devjamescollier

About the STM32-Based Programmable Waveform Generator PCB

STM32-Based Programmable Waveform Generator is an open source STM32 PCB design by devjamescollier, published on GitHub under the CERN-OHL-P-2.0 license. It is a 2-layer board measuring 52 × 48 mm, with 45 components from 28 distinct parts.

Its main chip is the C5456169, from the STM32 family. Other key parts include the C623655, C129334 and C27204. By type, the board carries 15 resistors, 11 capacitors, 5 diodes, 4 ICs, 3 connectors and 3 switches.

It belongs with the test & measurement designs in this gallery.

From the project

USB-powered STM32 function generator with an MCP4901 DAC producing sine, triangle, and square waves, with adjustable amplitude and button mode selection.

USB-powered programmable function generator built around an STM32C031K6T6 microcontroller and MCP4901 DAC. Generates clean sine, triangle, and square waveforms with amplitude control via potentiometer, mode selection via buttons, and visual feedback through status/signal LEDs.

Designed for lab and bench use with an SWD programming header, multiple test points, and robust power protection.

STM32-Based Programmable Waveform Generator, from the project README
From the project README

Main components on the STM32-Based Programmable Waveform Generator

C5456169C623655C129334C27204

STM32-Based Programmable Waveform Generator bill of materials (BOM)

45 components, 28 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
C5456169
STM32C031K6Tx
U1
1
C623655
MCP4901
U2
1
C129334
LM1117IMP-3.3/NOPB
U4
1
C27204
TLV2372
U5
2
C67272
IRLML0030
Q3, Q4
1
C492413
Conn_01x05
J1
1
C2931352
USB_B_Micro
J2
1
C158012
Conn_01x02
J3
1
C719176
10k
RV1
1
C93157
SIGNAL_SW
SW1
1
C93157
RESET_SW
SW2
1
C93157
SETTINGS_SW
SW3
1
C99561
250mA
TH1
5
C84256
LED_Red
D1, D2, D3, D4, D5
1
C28260
2.2n
C1
1
C9807
10u
C2
5
C49678
100n
C3, C4, C5, C9, C10
1
C15850
10u
C6
2
C7171
10u
C7, C8
1
C49678
100nF
C11
Show 8 more
QtyPartRefs
1
C28636
560
R1
2
C17673
4k7
R2, R4
1
C17772
6.8k
R3
3
C17414
10k
R5, R7, R11
5
C17557
220
R6, R10, R12, R13, R14
1
C4382
5k6
R8
1
C17514
1M
R9
1
C17720
49.9
R15

STM32-Based Programmable Waveform Generator design files

The KiCad project lives in the devjamescollier/STM32-Based_Programmable_Waveform_Generator repository on GitHub; these links point at the commit this page was built from.

STM32-Based Programmable Waveform Generator: common questions

What microcontroller does the STM32-Based Programmable Waveform Generator use?

The STM32-Based Programmable Waveform Generator is built around the C5456169, from the STM32 family.

How big is the STM32-Based Programmable Waveform Generator PCB?

The STM32-Based Programmable Waveform Generator measures 52 × 48 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the STM32-Based Programmable Waveform Generator?

45 components, from 28 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the STM32-Based Programmable Waveform Generator design files?

From the devjamescollier/STM32-Based_Programmable_Waveform_Generator repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the STM32-Based Programmable Waveform Generator design in my own project?

Yes, under the terms of its CERN-OHL-P-2.0 license, which devjamescollier chose for the repository.

Can I test firmware for the STM32-Based Programmable Waveform Generator without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.

Similar boards