HardLabs

Canview

digitie·canview·hardware/communicator/kicad/04_stm32.kicad_sch

This repository ships a schematic but no board layout.
Simulate this board

About the Canview PCB

Canview is an open source STM32 PCB design by digitie, published on GitHub under the GPL-3.0 license. It is a board, with 18 components from 6 distinct parts.

Its main chip is the STM32G474CEU6, from the STM32 family. By type, the board carries 10 resistors, 7 capacitors and 1 IC.

From the project

이 디렉터리는 R1-review 제안 회로의 검토 산출물을 보관한다. 현재 상태는 제작 정본이 아니며 차량 CAN 연결·송신 승인도 아니다.

이 디렉터리는 R1-review 제안 회로의 검토 산출물을 보관한다. 현재 상태는 제작 정본이 아니며 차량 CAN 연결·송신 승인도 아니다.

- kicad/communicator.kicadsch: 전원/USB, STM32/ESP32, CAN PHY/gate, MTi7/BMP384, GPS, 24개 테스트 패드의 28개 상세 sheet와 root - bom.csv: MPN·footprint·source·DNP·sheet가 포함된 검토용 BOM - netlist.xml, communicator.net: KiCad가 실제 내보낸 XML/sexpr netlist - pinmap.csv: KiCad symbol pin과 net을 펼친 기계 판독 표 - connectivity.json: source에서 생성된 sheet·component·net 연결 모델과 provenance - erc.json: KiCad ERC 결과 - preview.png, schematic.pdf: 사람이 검토할 수 있는 export - ../libraries/: 이 회로에서 사용하는 symbol·footprint 사본 - ../references/manifest.json: 부품 원문과…

Main components on the Canview

STM32G474CEU6

Canview bill of materials (BOM)

18 components, 6 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
STM32G474CEU6
U10
5
GEN-C-0402-100n-16V-X7R
100n
C36, C37, C38, C40, C42
1
GEN-C-0603-4.7u-16V-X7R
4.7u
C39
1
GEN-C-0603-1u-16V-X7R
1u
C41
1
GEN-R-0402-0-1%
0
R34
9
GEN-R-0402-10k-1%
10k
R35, R36, R37, R38, R39, R40, R41, R42 +1

Canview design files

The KiCad project lives in the digitie/canview repository on GitHub; these links point at the commit this page was built from.

Canview: common questions

What microcontroller does the Canview use?

The Canview is built around the STM32G474CEU6, from the STM32 family.

How many components are on the Canview?

18 components, from 6 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the Canview design files?

From the digitie/canview repository on GitHub, which has the schematic, a netlist and the BOM; the links under Design files point to each one.

Can I use the Canview design in my own project?

Yes, under the terms of its GPL-3.0 license, which digitie chose for the repository.

Can I test firmware for the Canview without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.

Similar boards