Stack controller
About the Stack controller PCB
Stack controller is an open source PCB design by emperor-hadrian, published on GitHub. It is a 2-layer board measuring 208 × 159 mm, with 53 components from 9 distinct parts.
By type, the board carries 47 ICs and 6 resistors.
From the project
Design for a DIY computer
The timing will be completely redone: A single normal clock signal, not the stupid "AB Alternating" I made up for the original. The PC will be incremented and a new instruction fetched during any non-flow-control instructions except when the GPRAM is used and the PC is in the same RAM chip (the RAM chips have 15 address lines each) as whatever is being accessed. The bus timing will also be very flexible and will be faster when possible but still slow when the memory is being accessed twice for example. Bus read/write addresses are both now 5 bits. The WRITE/MOVE instruction formats will…
Stack controller bill of materials (BOM)
53 components, 9 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 12 | ~ | DIP-16_W7.62mm | U1, U2, U3, U4, U14, U15, U16, U17 +4 |
| 1 | ~ | PinHeader_1x23_P2.54mm_Vertical | U5 |
| 9 | ~ | DIP-20_W7.62mm | U6, U7, U8, U9, U12, U18, U26, U29 +1 |
| 2 | ~ | DIP-28_W15.24mm | U10, U11 |
| 8 | ~ | DIP-14_W7.62mm | U13, U19, U24, U25, U27, U28, U31, U47 |
| 1 | ~ | PinHeader_1x08_P2.54mm_Vertical | U32 |
| 1 | ~ | PinHeader_1x16_P2.54mm_Vertical | U33 |
| 13 | ~ | jumper | U34, U35, U36, U37, U38, U39, U40, U41 +5 |
| 6 | 1k | 0.4_pitch_resistor | R1, R2, R3, R4, R5, R6 |
Stack controller design files
The KiCad project lives in the emperor-hadrian/stack_machine repository on GitHub; these links point at the commit this page was built from.
Stack controller: common questions
How big is the Stack controller PCB?
The Stack controller measures 208 × 159 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Stack controller?
53 components, from 9 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Stack controller design files?
From the emperor-hadrian/stack_machine repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Stack controller design in my own project?
The repository has no license, so all rights stay with emperor-hadrian. Use it as a reference, and ask the author before reusing the design.
More boards in stack_machine
Vector digital controller
428 × 293 mm156 parts2LNo license0
ALU
296 × 139 mm59 parts2LNo license0
Gpram
201 × 169 mm55 parts2LNo license0
Led matrix controller
268 × 99.1 mm52 parts2LNo license0
Control unit
165 × 118 mm50 parts2LNo license0
Main board
190 × 125 mm48 parts2LNo license0
Prog mem
157.5 × 127.5 mm39 parts2LNo license0
Call stack
140.5 × 100 mm27 parts2LNo license0
Godzilla
64 × 56 mm9 parts2LNo license0
Breakout 32 DIP 0 6 inch
36.1 × 43.7 mm3 parts2LNo license0