Shoto stabilizer
Fabian0520·Shoto
About the Shoto stabilizer PCB
Shoto stabilizer is an open source STM32 PCB design by Fabian0520, published on GitHub. It is a 2-layer board measuring 252 × 81.3 mm, with 97 components from 6 distinct parts.
Its main chip is the STM32F030C6Tx, from the STM32 family. By type, the board carries 48 relays, 48 diodes and 1 IC.
Main components on the Shoto stabilizer
Shoto stabilizer bill of materials (BOM)
97 components, 6 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | STM32F030C6Tx | LQFP-48_7x7mm_P0.5mm | U1 |
| 46 | KEYSW | Kailh_MX_Socket | K1, K2, K3, K4, K5, K6, K7, K8 +38 |
| 1 | KEYSW | SW_Cherry_MX1A_2.25u_PCB | K44 |
| 1 | KEYSW | SW_Cherry_MX1A_2.75u_PCB | K45 |
| 1 | SMF9.0CA D | D_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D1 |
| 47 | D | D_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D2, D3, D4, D5, D6, D7, D8, D9 +39 |
Shoto stabilizer design files
The KiCad project lives in the Fabian0520/Shoto repository on GitHub; these links point at the commit this page was built from.
- Layoutshoto_stabilizer.kicad_pcb
- BOMBOM.xlsx
Shoto stabilizer: common questions
What microcontroller does the Shoto stabilizer use?
The Shoto stabilizer is built around the STM32F030C6Tx, from the STM32 family.
How big is the Shoto stabilizer PCB?
The Shoto stabilizer measures 252 × 81.3 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Shoto stabilizer?
97 components, from 6 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Shoto stabilizer design files?
From the Fabian0520/Shoto repository on GitHub, which has the KiCad layout and the BOM; the links under Design files point to each one.
Can I use the Shoto stabilizer design in my own project?
The repository has no license, so all rights stay with Fabian0520. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Shoto stabilizer without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.
More boards in Shoto
Similar boards
STM32
LumenPnP Motherboard
opulo-inc
149 × 95 mm296 parts4LCC-BY-SA-4.03.7kSTM32
AxxSolder
AxxAxx
39 × 82.5 mm122 parts2LGPL-3.01.7kSTM32
LibreVNA
jankae
122 × 98 mm592 parts6LGPL-3.01.6kSTM32
AIOC
skuep
21 × 31.5 mm47 parts2LMIT1.4kSTM32
Ferris
pierrechevalier83
208.8 × 86.8 mm102 parts2LSHL-2.11.3kSTM32
176 pin board
rusefi
61.8 × 73.2 mm76 parts2LGPL-3.01.2k