HardLabs

DattaLab-HumidityChamber

HMS-RIC·DattaLab-HumidityChamber·Humidity Chamber PCB - KiCAD/Datta Lab Humidity Chamber PCB.kicad_pcb

DattaLab-HumidityChamber PCB layout, top view — open source NXP board by HMS-RIC

About the DattaLab-HumidityChamber PCB

DattaLab-HumidityChamber is an open source NXP PCB design by HMS-RIC, published on GitHub. It is a 2-layer board measuring 190.5 × 114.3 mm, with 46 components from 28 distinct parts.

Its main chip is the Teensy4.1, from the NXP family. By type, the board carries 25 connectors, 15 resistors, 3 test points, 1 IC, 1 switch and 1 diode.

It belongs with the sensors designs in this gallery.

From the project

Controller PCB for humidity chambers

Main components on the DattaLab-HumidityChamber

Teensy4.1

DattaLab-HumidityChamber bill of materials (BOM)

46 components, 28 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
Teensy4.1
U1
1
BNC-1
J1
1
BNC-2
J2
1
Cam-1
J3
1
Cam-2
J4
1
Cam-3
J5
1
GPIO Breakout Header
J6
1
+24 VDC
J7
1
A00-432-262-450
J8
2
MFC 1
J9, J17
2
MFC 3
J10, J18
5
I2C_STANDARDQWIIC
J11, J12, J19, J20, J25
2
MFC 2
J13, J21
2
MFC 4
J14, J22
2
MFM 1
J15, J23
2
MFM 2
J16, J24
1
500SSP1S1M6QEA
SW1
1
Gnd
TP1
1
24V
TP2
1
3V3
TP3
Show 8 more
QtyPartRefs
1
LED
D1
1
R
R1
2
1.2k
R2, R8
4
10k
R3, R4, R9, R10
2
560
R5, R11
2
2.7k
R6, R12
2
12k
R7, R13
2
5.6k
R14, R15

DattaLab-HumidityChamber design files

The KiCad project lives in the HMS-RIC/DattaLab-HumidityChamber repository on GitHub; these links point at the commit this page was built from.

DattaLab-HumidityChamber: common questions

What microcontroller does the DattaLab-HumidityChamber use?

The DattaLab-HumidityChamber is built around the Teensy4.1, from the NXP family.

How big is the DattaLab-HumidityChamber PCB?

The DattaLab-HumidityChamber measures 190.5 × 114.3 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the DattaLab-HumidityChamber?

46 components, from 28 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the DattaLab-HumidityChamber design files?

From the HMS-RIC/DattaLab-HumidityChamber repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the DattaLab-HumidityChamber design in my own project?

The repository has no license, so all rights stay with HMS-RIC. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the DattaLab-HumidityChamber without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug NXP firmware against it before you order a PCB.

Similar boards