Peps pr1-stm32
About the Peps pr1-stm32 PCB
Peps pr1-stm32 is an open source STM32 PCB design by hosjpps, published on GitHub. It is a board, with 20 components from 14 distinct parts.
Its main chip is the STM32F103C8T6, from the STM32 family. By type, the board carries 6 resistors and 5 capacitors.
From the project
Программирование электронных приборов и систем: ПР1 (STM32F103C8, KiCad)
- firmware/src/ — программы на Си, firmware/build/.hex — файлы прошивки. - kicad/ — проект и схема KiCad, лист с основной надписью по ГОСТ (.pdf). - PR1Proteus/wokwi/ — модель для симулятора Wokwi и результаты моделирования.
Заголовок stm32f10x.h в CooCox CoIDE подключается компонентом CMSIS BOOT. Для сборки вне CoIDE используется официальный CMSIS от ST (firmware/cmsis/) через обёртку firmware/compat/stm32f10x.h — имена регистров и битов те же.
Peps pr1-stm32 bill of materials (BOM)
20 components, 14 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | STM32F103C8T6 | DD1 | |
| 1 | Зуммер | HA1 | |
| 1 | Зелёный | HL1 | |
| 1 | Красный | HL2 | |
| 1 | 10k | RP1 | |
| 1 | Кнопка | SB1 | |
| 1 | 1N4148 | VD1 | |
| 1 | BC547 | VT1 | |
| 1 | 8MHz | ZQ1 | |
| 2 | 22p | C1, C2 | |
| 3 | 0.1u | C3, C4, C5 | |
| 3 | 10k | R1, R2, R3 | |
| 2 | 330 | R4, R5 | |
| 1 | 1k | R6 |
Peps pr1-stm32 design files
The KiCad project lives in the hosjpps/peps-pr1-stm32 repository on GitHub; these links point at the commit this page was built from.
Peps pr1-stm32: common questions
What microcontroller does the Peps pr1-stm32 use?
The Peps pr1-stm32 is built around the STM32F103C8T6, from the STM32 family.
How many components are on the Peps pr1-stm32?
20 components, from 14 distinct parts. The full bill of materials is listed on this page.
Where can I download the Peps pr1-stm32 design files?
From the hosjpps/peps-pr1-stm32 repository on GitHub, which has the schematic; the links under Design files point to each one.
Can I use the Peps pr1-stm32 design in my own project?
The repository has no license, so all rights stay with hosjpps. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Peps pr1-stm32 without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.
Similar boards
STM32LumenPnP Motherboard
opulo-inc
149 × 95 mm296 parts4LCC-BY-SA-4.03.7k
STM32AxxSolder
AxxAxx
39 × 82.5 mm122 parts2LGPL-3.01.7k
STM32LibreVNA
jankae
122 × 98 mm592 parts6LGPL-3.01.6k
STM32AIOC
skuep
21 × 31.5 mm47 parts2LMIT1.4k
STM32Ferris
pierrechevalier83
208.8 × 86.8 mm102 parts2LSHL-2.11.3k
STM32176 pin board
rusefi
61.8 × 73.2 mm76 parts2LGPL-3.01.2k