Stm32-falling sticks

Iam-Madman·stm32-falling-sticks·pcb/stm32-falling-sticks/stm32-falling-sticks.kicad_pcb

Stm32-falling sticks PCB layout, top view — open source board by Iam-Madman

About the Stm32-falling sticks PCB

Stm32-falling sticks is an open source PCB design by Iam-Madman, published on GitHub. It is a 2-layer board measuring 112 × 87 mm, with 69 components from 17 distinct parts.

Other key parts include the YAAJ_BluePill_Part_Like_SWD_Breakout. By type, the board carries 35 resistors, 11 transistors, 11 connectors, 11 diodes and 1 IC.

From the project

A DIY reaction-based "falling sticks" game controller built around an STM32 Bluepill.

A DIY reaction-based "falling sticks" game controller built around an STM32 Bluepill.

- STM32 Bluepill as the main controller - 10x electromagnet drivers (12v) — MOSFET-switched, each with a flyback protection diode and pulldown resistor - 10x Hall effect sensors (5v) for stick drop/position detection - LCD output support for game status/score - Buzzer (12v) support, driven off the same MOSFET channels as the electromagnets - Start button input to trigger the game - Single-layer PCB — 0-ohm jumper resistors used in place of vias/second layer for a few connections - CNC-mill optimized trace…

Stm32-falling sticks, from the project README
From the project README

Main components on the Stm32-falling sticks

Stm32-falling sticks bill of materials (BOM)

69 components, 17 distinct parts.

QtyPartRefs
1
YAAJ_BluePill_Part_Like_SWD_Breakout
U1
11
AO3400A
Q1, Q2, Q3, Q4, Q5, Q6, Q7, Q8 +3
1
MAG_01-05_OUT
J1
1
HAL_01-05_IN
J2
1
LCD_OUT
J3
1
MAG_06-10_OUT
J4
1
HAL_06-10_IN
J5
1
START_IN
J6
1
POT_IN
J7
1
MP1584EN
J8
1
Screw_Terminal_01x02
J9
1
BUZ_OUT
J11
1
Barrel_Jack_MountingPin
J12
11
SS34
D1, D2, D3, D4, D5, D6, D7, D8 +3
13
0
R2, R3, R4, R5, R27, R28, R29, R31 +5
11
10k
R6, R7, R8, R9, R10, R21, R22, R23 +3
11
100
R11, R12, R13, R14, R15, R16, R17, R18 +3

Stm32-falling sticks design files

The KiCad project lives in the Iam-Madman/stm32-falling-sticks repository on GitHub; these links point at the commit this page was built from.

Stm32-falling sticks: common questions

How big is the Stm32-falling sticks PCB?

The Stm32-falling sticks measures 112 × 87 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Stm32-falling sticks?

69 components, from 17 distinct parts. The full bill of materials is listed on this page.

Where can I download the Stm32-falling sticks design files?

From the Iam-Madman/stm32-falling-sticks repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.

Can I use the Stm32-falling sticks design in my own project?

The repository has no license, so all rights stay with Iam-Madman. Use it as a reference, and ask the author before reusing the design.