Stm32-fan ctrl

joubiti·stm32-fan-ctrl·Hardware/fan-ctrl.kicad_pcb

Stm32-fan ctrl PCB layout, top view — open source STM32 board by joubiti

About the Stm32-fan ctrl PCB

Stm32-fan ctrl is an open source STM32 PCB design by joubiti, published on GitHub under the MIT license. It is a 4-layer board measuring 64 × 44 mm, with 43 components from 28 distinct parts.

Its main chip is the STM32G070RBT6, from the STM32 family. Other key parts include the 826629-3, MP2359DT-LF-Z, XDJK-0051-025 and AMS1117-3.3. By type, the board carries 13 capacitors, 11 resistors, 6 ICs, 3 test points, 3 diodes and 2 transistors.

From the project

12V fan controller (4 layer board designed with KiCAD, manufactured at JLCPCB) based on STM32 using PID control

This project implements a closed-loop fan controller on a custom 4-layer PCB (manufactured at JLCPCB) with an STM32G0 micrcontroller. The fan speed is controlled using a PWM signal and regulated to a target RPM using a PID controller. The tachometer output of the fan is measured with a timer input capture unit, filtered, and fed into the control loop. Fairly satisfactory control performances have been achieved with Kp=0.01, Ki=0.015, and Kd = 0.001 at 10Hz.

Stm32-fan ctrl, from the project README
From the project README

Main components on the Stm32-fan ctrl

Stm32-fan ctrl bill of materials (BOM)

43 components, 28 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
STM32G070RBT6
U1
2
826629-3
U2, U3
1
MP2359DT-LF-Z
U4
1
XDJK-0051-025
U5
1
AMS1117-3.3
U6
1
AO3401A
Q1
1
AO3400A
Alpha & Omega Semicon
Q2
1
CRYSTAL_GND24
Crystal_GND24
Y1
1
DB127S-3.5-4P-GN
CN1
1
500MA
500mA
F1
3
TestPoint
TP9, TP10, TP11
1
LED
D1
1
LED
D2
1
B5819W_C8598
D3
1
600 @ 600 MHz
FB1
1
4.7U
4.7u
L1
4
100N
100n
C1, C2, C3, C7
1
4.7U
4.7u
C4
2
10P
10p
C5, C6
5
10U
10u
C8, C10, C11, C12, C13
Show 8 more
QtyPartRefs
1
10N
10n
C9
1
49K9
49k9
R1
2
1k
R2, R8
2
10K
10k
R3, R11
1
100K
100k
R4
1
9K1
9k1
R7
3
10K
10k
R9, R10, R13
1
100
R12

Stm32-fan ctrl design files

The KiCad project lives in the joubiti/stm32-fan-ctrl repository on GitHub; these links point at the commit this page was built from.

Stm32-fan ctrl: common questions

What microcontroller does the Stm32-fan ctrl use?

The Stm32-fan ctrl is built around the STM32G070RBT6, from the STM32 family.

How big is the Stm32-fan ctrl PCB?

The Stm32-fan ctrl measures 64 × 44 mm, has 4 copper layers and is 1.6 mm thick.

How many components are on the Stm32-fan ctrl?

43 components, from 28 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the Stm32-fan ctrl design files?

From the joubiti/stm32-fan-ctrl repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the Stm32-fan ctrl design in my own project?

Yes, under the terms of its MIT license, which joubiti chose for the repository.

Can I test firmware for the Stm32-fan ctrl without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.

Similar boards