Pulse oximeter

khomyakova228-cell·pulse-oximeter

Pulse oximeter PCB layout, top view — open source STM32 board by khomyakova228-cell

About the Pulse oximeter PCB

Pulse oximeter is an open source STM32 PCB design by khomyakova228-cell, published on GitHub. It is a 2-layer board measuring 78 × 79.5 mm, with 93 components from 17 distinct parts.

Its main chip is the STM32F030C8T6, from the STM32 family. By type, the board carries 40 resistors, 29 capacitors, 3 switches and 1 crystal.

From the project

- Задание - 1. Библиотека компонентов (УГО + посадочные места) - 2. Схема электрическая принципиальная - 3. Файл печатной платы - 4. Скрипт проверки и выпуска (bash / bat) - 5. Git-репозиторий и GitHub - Заключение: выполнение пунктов задания

- Задание - 1. Библиотека компонентов (УГО + посадочные места) - 2. Схема электрическая принципиальная - 3. Файл печатной платы - 4. Скрипт проверки и выпуска (bash / bat) - 5. Git-репозиторий и GitHub - Заключение: выполнение пунктов задания

Общее задание: создать проект печатной платы в KiCad. Проект должен содержать:

1. Библиотеку компонентов (УГО + посадочные места). УГО компонентов оформить по ГОСТ. Библиотека должна подключаться к проекту как git-сабмодуль. Пути библиотек должны быть относительными. 2. Схему электрическую принципиальную, оформленную по ГОСТ (как минимум рамка и…

Pulse oximeter, from the project README
From the project README

Pulse oximeter bill of materials (BOM)

93 components, 17 distinct parts.

QtyPartRefs
1
61300311121
Conn_01x03
Würth Elektronik
X1
7
OPA340PA
OPA340P
Texas Instruments
DA1, DA2, DA3, DA4, DA5, DA6, DA7
1
КР590КН2
—
DA8
1
LM1117T-ADJ/NOPB
LM1117T-ADJ
Texas Instruments
DA9
1
STM32F030C8T6
STMicroelectronics
DD1
1
FT232RL-REEL
FT232RL
FTDI
DD2
2
TSAL6200
Vishay
HL1, HL2
3
B3F-1000
Omron
SW1, SW2, SW3
1
BPW34
Vishay
VD1
4
1N4733A
5V1
Vishay
VD2, VD3, VD4, VD5
2
BD139-16
STMicroelectronics
VT1, VT2
29
RDER71H104K0P1H03B
100n
Murata
C1, C2, C3, C4, C5, C6, C7, C8 +21
12
MFR50SFTE52-10K
10k
YAGEO
R1, R4, R5, R6, R7, R11, R12, R18 +4
9
MFR50SFTE52-22K
22k
YAGEO
R2, R3, R9, R10, R16, R17, R22, R35 +1
9
MFR50SFTE52-390R
390
YAGEO
R8, R14, R24, R25, R27, R30, R31, R42 +1
6
3296W-1-103LF
10k
Bourns
R13, R19, R20, R29, R37, R44
4
MFR50SFTE52-2K2
2.2k
YAGEO
R15, R26, R34, R43

Pulse oximeter design files

The KiCad project lives in the khomyakova228-cell/pulse-oximeter repository on GitHub; these links point at the commit this page was built from.

Pulse oximeter: common questions

What microcontroller does the Pulse oximeter use?

The Pulse oximeter is built around the STM32F030C8T6, from the STM32 family.

How big is the Pulse oximeter PCB?

The Pulse oximeter measures 78 × 79.5 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Pulse oximeter?

93 components, from 17 distinct parts. The full bill of materials is listed on this page.

Where can I download the Pulse oximeter design files?

From the khomyakova228-cell/pulse-oximeter repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.

Can I use the Pulse oximeter design in my own project?

The repository has no license, so all rights stay with khomyakova228-cell. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the Pulse oximeter without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.

Similar boards