Tx2
Kreyl·tirusse·Tx2_hw/Tx2.kicad_pcb
About the Tx2 PCB
Tx2 is an open source STM32 PCB design by Kreyl, published on GitHub. It is a 2-layer board measuring 66 × 39 mm, with 54 components from 32 distinct parts.
Its main chip is the STM32F10X-48, from the STM32 family. By type, the board carries 26 capacitors, 7 fuses, 7 resistors, 2 test points, 1 antenna and 1 switch.
From the project
Sword which lights up when orcs are near
Tx2 bill of materials (BOM)
54 components, 32 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ANT_PCB_MONO | ANT_868_MEANDER | ANT1 |
| 1 | LP2951 | SO8E | DA1 |
| 1 | AAT3221 | SOT23-5 | DA2 |
| 1 | CC1101 | QFN20 | DD1 |
| 1 | STM32F10X-48 | LQFP48 | DD2 |
| 7 | FUSE0R | SOLDERFUSE | F1, F2, F3, F4, F5, F6, F7 |
| 1 | SWITCH | SIL-3 | SW1 |
| 2 | TESTPOINT | TESTPOINT_1MM | TP1, TP2 |
| 1 | ST_SWD | SIL-4 | XL1 |
| 1 | CONN_3 | SIL-3 | XL2 |
| 1 | CONN_1 | SIL-1 | XL3 |
| 1 | PWRCONN | PWRCON2PIN | XL10 |
| 1 | 27MHz | CRYSTAL_03225C4 | XTAL1 |
| 1 | 12.0MHz | CRYSTAL_0503x4-4 | XTAL2 |
| 1 | 100pF | CAP_0603 | C1 |
| 2 | 1.5pF | CAP_0603 | C2, C5 |
| 1 | 1pF | CAP_0603 | C3 |
| 2 | 220pF | CAP_0603 | C4, C11 |
| 2 | 3.3pF | CAP_0603 | C6, C8 |
| 2 | 10n | CAP_0603 | C7, C9 |
Show 12 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 8 | 0.1u | CAP_0603 | C10, C14, C17, C18, C19, C21, C22, C23 |
| 2 | 10pF | CAP_0603 | C12, C13 |
| 2 | 20pF | CAP_0603 | C15, C16 |
| 2 | 10u | CAP_0805 | C20, C24 |
| 1 | 1u | CAP_0603 | C25 |
| 1 | 1000pF | CAP_0603 | C26 |
| 1 | 100R | RES_0603 | R1 |
| 1 | 220R | RES_0603 | R2 |
| 1 | 56k | RES_0603 | R3 |
| 1 | 20k | RES_0603 | R4 |
| 1 | 12k | RES_0603 | R5 |
| 2 | 100k | RES_0603 | R25, R26 |
Tx2 design files
The KiCad project lives in the Kreyl/tirusse repository on GitHub; these links point at the commit this page was built from.
- LayoutTx2_hw/Tx2.kicad_pcb
- SchematicTx2_hw/Tx2.kicad_sch
Tx2: common questions
What microcontroller does the Tx2 use?
The Tx2 is built around the STM32F10X-48, from the STM32 family.
How big is the Tx2 PCB?
The Tx2 measures 66 × 39 mm, has 2 copper layers and is 1.6002 mm thick.
How many components are on the Tx2?
54 components, from 32 distinct parts. The full bill of materials is listed on this page.
Where can I download the Tx2 design files?
From the Kreyl/tirusse repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Tx2 design in my own project?
The repository has no license, so all rights stay with Kreyl. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Tx2 without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.
More boards in tirusse
Similar boards
STM32
LumenPnP Motherboard
opulo-inc
149 × 95 mm296 parts4LCC-BY-SA-4.03.7kSTM32
Type g
google
169 × 30 mm24 parts2LApache-2.02.9kSTM32
Main panel
google
234 × 84 mm26 parts4LApache-2.02.9kSTM32
Base
google
52.3 × 52.3 mm36 parts2LApache-2.02.9kSTM32
Type a
google
150 × 30 mm14 parts2LApache-2.02.9kSTM32
Type c
google
188 × 30 mm17 parts2LApache-2.02.9k