UV bench Rev C

L-A-7·Electronic-design·projects/01-uv-bench/hardware/uv-bench/uv-bench.kicad_pcb

UV bench Rev C PCB layout, top view — open source STM32 board by L-A-7

About the UV bench Rev C PCB

UV bench Rev C is an open source STM32 PCB design by L-A-7, published on GitHub. It is a 2-layer board measuring 58 × 32 mm, with 25 components from 15 distinct parts.

Its main chip is the ST STM32C031F6P6, from the STM32 family. Other key parts include the Microchip MCP1700T-3302E/TT. By type, the board carries 8 capacitors, 8 resistors, 3 connectors, 2 ICs, 2 diodes and 1 transistor.

From the project

Learning workspace for electronics and PCB design (KiCad 10, STM32): UV bench and following projects

- How and why, block by block, plus the KiCad notes (§8): docs/rev-b-simple.md. - Generated parts list with nets: docs/parts-list.md.

The sensor head uses the same two generators, pointed at its own design module. It has two hand-placed tracks, so no autorouter:

- The autorouter isn't deterministic. Each run gives a slightly different, equally valid routing. Always finish with kicad-check.sh. - Build a copy without touching the project: set UVBPRJ=/some/dir/uv-bench (a folder holding a copy of the .kicadpro, .kicaddru and lib tables). All scripts honour it. - Once you edit the PCB by hand…

Main components on the UV bench Rev C

UV bench Rev C bill of materials (BOM)

25 components, 15 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
Microchip MCP1700T-3302E/TT
MCP1700-3.3
U1
1
ST STM32C031F6P6
STM32C031F6P6
U2
1
Alpha & Omega AO3400A
AO3400A
Q1
1
JST B4B-PH-K-S
I2C + 5V (JST-PH)
J1
1
Samtec FTSH-107-01-L-DV-K
STDC14 (SWD + VCP)
J3
1
JST B2B-PH-K-S
remote PD (JST-PH)
J4
1
Bourns PEC09-2xxxF-Sxxxx (with switch; pick the shaft length)
PEC09 + push
SW1
1
ams OSRAM SFH 2401
SFH 2401
D1
1
green
D2
4
10u
C1, C2, C3, C7
4
100n
C4, C5, C6, C8
1
any 3.9 R 1 W 2512, e.g. Yageo RC2512FK-073R9L
3R9 1W
R1
4
1k
R2, R5, R6, R7
2
100k
R3, R4
1
10k
R8

UV bench Rev C design files

The KiCad project lives in the L-A-7/Electronic-design repository on GitHub; these links point at the commit this page was built from.

UV bench Rev C: common questions

What microcontroller does the UV bench Rev C use?

The UV bench Rev C is built around the ST STM32C031F6P6, from the STM32 family.

How big is the UV bench Rev C PCB?

The UV bench Rev C measures 58 × 32 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the UV bench Rev C?

25 components, from 15 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the UV bench Rev C design files?

From the L-A-7/Electronic-design repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the UV bench Rev C design in my own project?

The repository has no license, so all rights stay with L-A-7. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the UV bench Rev C without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.

Similar boards