Disabledbabyironman
lohhaoyuan·disabledbabyironman·hardware/cuff/cuff.kicad_pcb
About the Disabledbabyironman PCB
Disabledbabyironman is an open source STM32 PCB design by lohhaoyuan, published on GitHub under the MIT license. It is a 2-layer board measuring 28.3 × 28.8 mm, with 18 components from 12 distinct parts.
Its main chip is the STM32F411CEUx, from the STM32 family. By type, the board carries 7 capacitors, 5 connectors, 3 resistors, 1 crystal and 1 diode.
From the project
Design files for 2026 CenTAD Project LM05
Disabledbabyironman bill of materials (BOM)
18 components, 12 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | 16Mhz | CX3225SB16000D0FPLCC | Y301 |
| 1 | FSR 1 | PinHeader_1x02_P2.54mm_Vertical | J1 |
| 1 | IMU SH | JST_SH_BM04B-SRSS-TB_1x04-1MP_P1.00mm_Vertical | J2 |
| 1 | Conn_01x04 | Untitled | J3 |
| 1 | stupid grove connector | GROVE-HW4-2.0 | J4 |
| 1 | Conn_01x04 | PinHeader_1x04_P2.54mm_Vertical | J302 |
| 1 | STM32F411CEUx | QFN-48-1EP_7x7mm_P0.5mm_EP5.6x5.6mm | MAIN501 |
| 1 | RED | led0603 | D301 |
| 1 | 2u2 | cap0603 | C301 |
| 6 | 0u1 | cap0603 | C302, C303, C304, C305, C306, C307 |
| 2 | 10K | res0603 | R1, R302 |
| 1 | 1K | res0603 | R301 |
Disabledbabyironman design files
The KiCad project lives in the lohhaoyuan/disabledbabyironman repository on GitHub; these links point at the commit this page was built from.
- Layouthardware/cuff/cuff.kicad_pcb
- Schematichardware/cuff/cuff.kicad_sch
Disabledbabyironman: common questions
What microcontroller does the Disabledbabyironman use?
The Disabledbabyironman is built around the STM32F411CEUx, from the STM32 family.
How big is the Disabledbabyironman PCB?
The Disabledbabyironman measures 28.3 × 28.8 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Disabledbabyironman?
18 components, from 12 distinct parts. The full bill of materials is listed on this page.
Where can I download the Disabledbabyironman design files?
From the lohhaoyuan/disabledbabyironman repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Disabledbabyironman design in my own project?
Yes, under the terms of its MIT license, which lohhaoyuan chose for the repository.
Can I test firmware for the Disabledbabyironman without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.
Similar boards
STM32
LumenPnP Motherboard
opulo-inc
149 × 95 mm296 parts4LCC-BY-SA-4.03.7kSTM32
Type g
google
169 × 30 mm24 parts2LApache-2.02.9kSTM32
Main panel
google
234 × 84 mm26 parts4LApache-2.02.9kSTM32
Base
google
52.3 × 52.3 mm36 parts2LApache-2.02.9kSTM32
Type a
google
150 × 30 mm14 parts2LApache-2.02.9kSTM32
Type c
google
188 × 30 mm17 parts2LApache-2.02.9k