Nitrokey Pro
Nitrokey·nitrokey-pro-hardware·src/cryptostick.kicad_pcb
About the Nitrokey Pro PCB
Nitrokey Pro is an open source STM32 PCB design by Nitrokey, published on GitHub. It is a 2-layer board measuring 21.8 × 16.3 mm, with 26 components from 16 distinct parts.
Its main chip is the STM32F103TB, from the STM32 family. Other key parts include the CAT6217-330 and DF5A5.6JE. By type, the board carries 11 capacitors, 8 resistors, 3 ICs, 2 connectors, 1 crystal and 1 diode.
From the project
Hardware design of the Nitrokey Pro device
Nitrokey Pro PCB Design ===================================================
Nitrokey Pro is a USB 32-bit computer with STM32F103 processor and an OpenPGP smart card. It has a minimalistic design, the MCU is running at 72MHz, and it has a SWD port for main flash ROM update.
This is Nitrokey PCB design for KiCAD, based on Niibe Yutaka's Flying Stone Tiny 01 (FST-01).
Main components on the Nitrokey Pro
Nitrokey Pro bill of materials (BOM)
26 components, 16 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | STM32F103TB | QFN-36-1EP_6x6mm_P0.5mm_EP4.1x4.1mm_ThermalVias | U1 |
| 1 | CAT6217-330 | TSOT-23-5 | U2 |
| 1 | DF5A5.6JE | SOT-553 | U3 |
| 1 | 12MHZ 12MHz | ABM8G | X1 |
| 1 | WM9364 SIM_JACKET | molex78646-3001 | J1 |
| 1 | WM3983 USB_A | USB-A-PLUG | J2 |
| 1 | DUAL_LED | KPHBM-2012SURKCGKC | D1 |
| 2 | 27PF 27pF | C_0402_1005Metric | C1, C2 |
| 6 | 0.1UF 0.1uF | C_0402_1005Metric | C3, C4, C5, C6, C7, C8 |
| 2 | 4.7UF 4.7uF | C_0402_1005Metric | C9, C11 |
| 1 | 0.01UF 0.01uF | C_0402_1005Metric | C10 |
| 2 | 510 | R_0402_1005Metric | R1, R2 |
| 2 | 10K 10k | R_0402_1005Metric | R3, R4 |
| 2 | 22 | R_0402_1005Metric | R5, R6 |
| 1 | 1.5K 1.5k | R_0402_1005Metric | R7 |
| 1 | 20K 20k | R_0402_1005Metric | R8 |
Nitrokey Pro design files
The KiCad project lives in the Nitrokey/nitrokey-pro-hardware repository on GitHub; these links point at the commit this page was built from.
- Layoutsrc/cryptostick.kicad_pcb
- Schematicsrc/cryptostick.kicad_sch
- BOMfabrication/v6/BOM.csv
Nitrokey Pro: common questions
What microcontroller does the Nitrokey Pro use?
The Nitrokey Pro is built around the STM32F103TB, from the STM32 family.
How big is the Nitrokey Pro PCB?
The Nitrokey Pro measures 21.8 × 16.3 mm, has 2 copper layers and is 1 mm thick.
How many components are on the Nitrokey Pro?
26 components, from 16 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Nitrokey Pro design files?
From the Nitrokey/nitrokey-pro-hardware repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Nitrokey Pro design in my own project?
The repository has no license, so all rights stay with Nitrokey. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Nitrokey Pro without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.
More boards in nitrokey-pro-hardware
Similar boards
STM32
LumenPnP Motherboard
opulo-inc
149 × 95 mm296 parts4LCC-BY-SA-4.03.7kSTM32
Type g
google
169 × 30 mm24 parts2LApache-2.02.9kSTM32
Main panel
google
234 × 84 mm26 parts4LApache-2.02.9kSTM32
Base
google
52.3 × 52.3 mm36 parts2LApache-2.02.9kSTM32
Type a
google
150 × 30 mm14 parts2LApache-2.02.9kSTM32
Type c
google
188 × 30 mm17 parts2LApache-2.02.9k