RP2040-PICO-PC rev C
About the RP2040-PICO-PC rev C PCB
RP2040-PICO-PC rev C is an open source PCB design by OLIMEX, published on GitHub under the GPL-3.0 license. It is a 2-layer board measuring 72 × 38.5 mm, with 61 components from 36 distinct parts.
Other key parts include the BL4054B-42TPRN and 74LVC125APW. By type, the board carries 29 resistors, 7 capacitors, 2 ICs, 1 connector, 1 LED and 1 diode.
It belongs with the power & battery, keyboards and audio designs in this gallery.
From the project
Mother board for Raspberry Pi RP2040-PICO which adds HDMI/DVI Audio SD-card Lipo charger UEEXT and USB-OTG allowing to make small PC with monitor and keyboard
This folder conaints design source files for each major hardware revisions.
There are also PDF exports of the schematic and BOM exports available.
The designs are made with KiCAD. Below you can find revision changes:
1. Con2 changed to qwst1 and pinout changed! 2. Imropoved the pads and the soldering of all bigger components. They should now be more sturdy.
1. Added diode D1 at the HDMI connector. R6 changed to 27k. 2. I2C1 fixed. SCL and SDA were swapped at the processor (3.3V). 3. Added needed resistors and capacitors and ferrite beads to SD_Card. 4. Board size increased.
Main components on the RP2040-PICO-PC rev C
RP2040-PICO-PC rev C bill of materials (BOM)
61 components, 36 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | BL4054B-42TPRN | SOT-23-5 | U1 |
| 1 | 74LVC125APW | 74LVC125A(TSSOP14-14_leads-4.4mm_body_width-SOT402-1) | U3 |
| 1 | CI0104P1VK0 (PH-4A) | CL0104PV1K0 | CON2 |
| 1 | open | SJ_1_SMALLER | 5V_ENABLE1 |
| 1 | 3.5mm PJ-W47S-05D2-LF | PJ-W47S-05D2-LF_5PIN_V2 | AUDIO_JACK_1 |
| 1 | DW02S | LIPO_BAT_VERTICAL_DW02S | BAT_CON1 |
| 1 | HN1x3 | HN1x3 | DBG1 |
| 1 | WPM2015-3/TR | SOT23 | FET1 |
| 2 | BSS138 | SOT23 | FET2, FET3 |
| 1 | FSMD035-1206 (NANOSMDC035F-2) | FUSE-1206 | FUSE1 |
| 1 | HDMI-SWM-19 | HDMI-SWM-19 | HDMI1 |
| 4 | Mounting_hole_Shield_3.3mm | Mounting_hole_Shield_3.3mm | MH1, MH2, MH3, MH4 |
| 1 | TFC-WPAPR-08-LF | TFC-WPAPR-08 | MICRO_SD1 |
| 1 | RMAT (4x0603) 100 K 5% | RA1206_(4X0603)_4B8_xx | RM1 |
| 1 | 2X(PN1X20(F-D-1X20-LF)) | RP_Pico2040 | RP2040_PLATFORM1 |
| 1 | YTS-A016-X | YTS-A016-X | RST1 |
| 1 | BH10S (B-D-02x5-LF) | BH10S | UEXT1 |
| 1 | MISB-SWMM-5B-LF | USB-MICRO_MISB-SWMM-5B_LF | USB1 |
| 1 | LED 0603 RED 300 mCd | LED_0603_KA | LED1 |
| 1 | 1N5819 (S4 SOD-123) | SOD-123_1C-2A_KA | D1 |
Show 16 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | 0805 600 OHM 2A HIGH CURRENT | L_0805_5MIL_DWS | L1 |
| 1 | 0603 10 UF 6.3V | C_0603_5MIL_DWS | C1 |
| 1 | 0603 1 UF 10V 10% X5R | C_0603_5MIL_DWS | C2 |
| 2 | 0805 47 UF 6.3V 20% X5R | C_0805_5MIL_DWS | C3, C7 |
| 3 | 0402 100 NF 10V 20% X5R | C_0402_5MIL_DWS | C4, C5, C6 |
| 1 | 0402 1.5 K 5% | R_0402_5MIL_DWS | R1 |
| 6 | 0402 2.2 K 5% | R_0402_5MIL_DWS | R2, R3, R15, R26, R27, R28 |
| 1 | 0402 2 K 5% | R_0402_5MIL_DWS | R4 |
| 1 | 0402 100 K 5% | R_0402_5MIL_DWS | R5 |
| 1 | 0402 27 K 5% | R_0402_5MIL_DWS | R6 |
| 9 | 0402 270 OHM 5% | R_0402_5MIL_DWS | R7, R8, R9, R10, R11, R12, R13, R14 +1 |
| 2 | 0603 1.8 K 5% | R_0603_5MIL_DWS | R16, R21 |
| 2 | 0402 100 OHM 5% | R_0402_5MIL_DWS | R17, R20 |
| 2 | 0402 220 OHM 5% | R_0402_5MIL_DWS | R18, R19 |
| 2 | NA/0402 | R_0402_5MIL_DWS | R22, R23 |
| 2 | 0402 10 K 5% | R_0402_5MIL_DWS | R24, R29 |
RP2040-PICO-PC rev C design files
The KiCad project lives in the OLIMEX/RP2040-PICO-PC repository on GitHub; these links point at the commit this page was built from.
RP2040-PICO-PC rev C: common questions
How big is the RP2040-PICO-PC rev C PCB?
The RP2040-PICO-PC rev C measures 72 × 38.5 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the RP2040-PICO-PC rev C?
61 components, from 36 distinct parts. The full bill of materials is listed on this page.
Where can I download the RP2040-PICO-PC rev C design files?
From the OLIMEX/RP2040-PICO-PC repository on GitHub, which has the KiCad layout; the links under Design files point to each one.
Can I use the RP2040-PICO-PC rev C design in my own project?
Yes, under the terms of its GPL-3.0 license, which OLIMEX chose for the repository.
byrantech
google