OxySwitch-HW
OxyHome·OxySwitch-HW
About the OxySwitch-HW PCB
OxySwitch-HW is an open source STM32 PCB design by OxyHome, published on GitHub under the CERN-OHL-S-2.0 license. It is a board, with 11 components from 10 distinct parts.
Its main chip is the STM32WB35CEU6A, from the STM32 family. By type, the board carries 4 capacitors, 2 crystals, 2 switches, 1 IC, 1 inductor and 1 resistor.
It belongs with the iot & wireless designs in this gallery.
From the project
HW part of OxySwitch - Zigbee 3.0 smart switch
HW part of OxySwitch - Zigbee 3.0 smart switch
All schematics are provided without any safety assurances and using them is at your own risk, unless final product is bought from a dealer with the certification given by law and not modified
Main components on the OxySwitch-HW
OxySwitch-HW bill of materials (BOM)
11 components, 10 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | STM32WB35CEU6A | STM32WB35CEU6A | IC201 |
| 1 | ABS05-32.768KHZ-9-T 32.768kHz/9pF | ABS0532768KHZ9T | Y201 |
| 1 | ABM11W-32.0000MHZ-8-D1X-T3 32MHz/8pF | ABM11W300000MHZ4B1UT3 | Y202 |
| 1 | SW_Push | SW201 | |
| 1 | SW_SPDT | SW202 | |
| 1 | 10u | L201 | |
| 2 | 8p | C201, C202 | |
| 1 | 4u7 | C203 | |
| 1 | C | C204 | |
| 1 | 10k | R201 |
OxySwitch-HW design files
The KiCad project lives in the OxyHome/OxySwitch-HW repository on GitHub; these links point at the commit this page was built from.
- Schematicmcu.kicad_sch
OxySwitch-HW: common questions
What microcontroller does the OxySwitch-HW use?
The OxySwitch-HW is built around the STM32WB35CEU6A, from the STM32 family.
How many components are on the OxySwitch-HW?
11 components, from 10 distinct parts. The full bill of materials is listed on this page.
Where can I download the OxySwitch-HW design files?
From the OxyHome/OxySwitch-HW repository on GitHub, which has the schematic; the links under Design files point to each one.
Can I use the OxySwitch-HW design in my own project?
Yes, under the terms of its CERN-OHL-S-2.0 license, which OxyHome chose for the repository.
Can I test firmware for the OxySwitch-HW without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.
Similar boards
STM32
LumenPnP Motherboard
opulo-inc
149 × 95 mm296 parts4LCC-BY-SA-4.03.7kSTM32
Type g
google
169 × 30 mm24 parts2LApache-2.02.9kSTM32
Base
google
52.3 × 52.3 mm36 parts2LApache-2.02.9kSTM32
Main panel
google
234 × 84 mm26 parts4LApache-2.02.9kSTM32
Type a
google
150 × 30 mm14 parts2LApache-2.02.9kSTM32
Type c
google
188 × 30 mm17 parts2LApache-2.02.9k