HardLabs

Stm32-camera

Scottapotamas·stm32-camera·Electronics/stm32-camera.kicad_pcb

Stm32-camera PCB layout, top view — open source STM32 board by Scottapotamas
Simulate this board

About the Stm32-camera PCB

Stm32-camera is an open source STM32 PCB design by Scottapotamas, published on GitHub. It is a 4-layer board measuring 36 × 36 mm, with 58 components from 30 distinct parts.

Its main chip is the STM32F429VET6, from the STM32 family. Other key parts include the AP2210K-ADJ and OV02640-VL9A. By type, the board carries 29 capacitors, 14 resistors, 5 ICs, 3 connectors, 2 crystals and 2 diodes.

From the project

Custom CMOS camera board with STM32.

General implementation notes during assignment and schematic capture. These are notes which don't make it onto the schematic due to length or relevance. Hopefully they might be useful during software dev.

- I2C2 peripheral is used for SSCB interface (configuration registers). - MCO (PA8) is used for the camera XCLK clock. Should clock at 24Mhz typical, 6Mhz minimum. This can be the HSI, HSE, a timer, etc. - DCMI interface is used for main camera connection (includes HSYNC/VSYNC/PIXCK pins etc) - PCLK is the camera strobe for 8-bit data on rising edge. - PWDN is the camera power down signal…

Main components on the Stm32-camera

STM32F429VET6AP2210K-ADJOV02640-VL9A

Stm32-camera bill of materials (BOM)

58 components, 30 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
STM32F429VET6
U1
3
AP2210K-ADJ
U2, U3, U4
1
OV02640-VL9A
U5
1
TEMT7000X01
Q1
1
CSTCE16M0V53A
X1
1
SWD
X2
1
MOLEX_47309-2651
CON1
1
CONN_01X08
P1
1
MOLEX_PICO_PTH_VERT_2_WAY
P2
1
M12_LENS_MOUNT_IR_SWITCHNG
MP1
1
B3U-1000P_SPST-NO_SMD
SW1
1
LED_GREEN_1608M
D1
1
LED_RED_1608M
D2
6
1UF_X5R_1005M
C1, C3, C4, C12, C24, C28
14
100NF_X7R_1005M
C2, C5, C6, C7, C8, C9, C10, C11 +6
7
2.2UF_X7R_1608M
C14, C15, C16, C17, C18, C19, C20
1
4.7UF_X5R_1005M
C23
1
100NF_X7R_1608M
C29
2
1K_1005M
R1, R2
1
51K_1005M
R3
Show 10 more
QtyPartRefs
1
82K_1005M
R4
1
47K_1005M
R5
1
56K2_1005M
R6
1
100K_1005M
R7
1
3K6_1005M
R8
1
47K_QUAD_ARRAY_1608M
R9
1
10K_1005M
R10
2
4K7_1005M
R11, R12
1
510K_1005M
R13
1
100R_1608M
R14

Stm32-camera design files

The KiCad project lives in the Scottapotamas/stm32-camera repository on GitHub; these links point at the commit this page was built from.

Stm32-camera: common questions

What microcontroller does the Stm32-camera use?

The Stm32-camera is built around the STM32F429VET6, from the STM32 family.

How big is the Stm32-camera PCB?

The Stm32-camera measures 36 × 36 mm, has 4 copper layers and is 1.6 mm thick.

How many components are on the Stm32-camera?

58 components, from 30 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the Stm32-camera design files?

From the Scottapotamas/stm32-camera repository on GitHub, which has the KiCad layout and the BOM; the links under Design files point to each one.

Can I use the Stm32-camera design in my own project?

The repository has no license, so all rights stay with Scottapotamas. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the Stm32-camera without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.

Similar boards