Blackmagic entropia clone
sergiomd4·blackmagic-entropia-clone·Hardware/bmp_entropia.kicad_pcb
About the Blackmagic entropia clone PCB
Blackmagic entropia clone is an open source STM32 PCB design by sergiomd4, published on GitHub under the CC0-1.0 license. It is a 2-layer board measuring 48.8 × 23.1 mm, with 34 components from 20 distinct parts.
Its main chip is the STM32F_48PIN, from the STM32 family. Other key parts include the TLV70033DCK. By type, the board carries 12 resistors, 10 capacitors, 4 LEDs, 2 ICs, 2 transistors and 1 crystal.
From the project
Board focused on embedded microcontrollers debugging
Black Magic Entropia Clone ========================================
Black Magic Entropia is similar to Black Magic Mini but only uses 0603 components and standard connectors.
It is an easy-to-use board used for debugging embedded microcontrollers. It supports several targets from manufacturers such as STMicroelectronics, Atmel, Nordic Semiconductor, NXP, Texas Instruments, Freescale, Silicon Labs, Xilinx or Raspberry Pi.
Main components on the Blackmagic entropia clone
Blackmagic entropia clone bill of materials (BOM)
34 components, 20 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | STM32F_48PIN | TQFP48 | U$1 |
| 1 | TLV70033DCK | SC70-5L | U$2 |
| 1 | 8MHz | HC49_S | Q1 |
| 1 | IRLML5103 | SOT23 | Q2 |
| 1 | MINI-USB-32005-301 | 32005-301 | X1 |
| 1 | — | JP1 | JP1 |
| 1 | — | MA04-1 | SV1 |
| 1 | — | MA05-2 | SV2 |
| 1 | green | CHIPLED_0603 | LED1 |
| 1 | red | CHIPLED_0603 | LED2 |
| 2 | yellow | CHIPLED_0603 | LED3, LED4 |
| 2 | 27p | C0603 | C1, C2 |
| 5 | 100n | C0603 | C3, C6, C7, C8, C9 |
| 1 | 1u | C0603 | C4 |
| 2 | 2u2 | C0603 | C5, C10 |
| 1 | 1k5 | R0603 | R1 |
| 2 | 22R | R0603 | R2, R3 |
| 4 | 470R | R0603 | R6, R7, R8, R9 |
| 2 | 4k7 | R0603 | R10, R13 |
| 3 | 10k | R0603 | R11, R12, R14 |
Blackmagic entropia clone design files
The KiCad project lives in the sergiomd4/blackmagic-entropia-clone repository on GitHub; these links point at the commit this page was built from.
Blackmagic entropia clone: common questions
What microcontroller does the Blackmagic entropia clone use?
The Blackmagic entropia clone is built around the STM32F_48PIN, from the STM32 family.
How big is the Blackmagic entropia clone PCB?
The Blackmagic entropia clone measures 48.8 × 23.1 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Blackmagic entropia clone?
34 components, from 20 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Blackmagic entropia clone design files?
From the sergiomd4/blackmagic-entropia-clone repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Blackmagic entropia clone design in my own project?
Yes, under the terms of its CC0-1.0 license, which sergiomd4 chose for the repository.
Can I test firmware for the Blackmagic entropia clone without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.
Similar boards
STM32
LumenPnP Motherboard
opulo-inc
149 × 95 mm296 parts4LCC-BY-SA-4.03.7kSTM32
Type g
google
169 × 30 mm24 parts2LApache-2.02.9kSTM32
Main panel
google
234 × 84 mm26 parts4LApache-2.02.9kSTM32
Base
google
52.3 × 52.3 mm36 parts2LApache-2.02.9kSTM32
Type a
google
150 × 30 mm14 parts2LApache-2.02.9kSTM32
Type c
google
188 × 30 mm17 parts2LApache-2.02.9k