Brushed dual esc

sigmondkukla·brushed-dual-esc·pcb/brushed-dual-esc.kicad_pcb

Brushed dual esc PCB layout, top view — open source STM32 board by sigmondkukla

About the Brushed dual esc PCB

Brushed dual esc is an open source STM32 PCB design by sigmondkukla, published on GitHub. It is a 2-layer board measuring 30 × 25 mm, with 21 components from 13 distinct parts.

Its main chip is the STM32C011F6U6, from the STM32 family. Other key parts include the AZ1117CR-5.0TRG1, TLV77133PDBVR and DRV8231ADDAR. By type, the board carries 10 capacitors, 5 ICs, 5 resistors and 1 diode.

It belongs with the robotics & motion, power & battery and usb & debug tools designs in this gallery.

From the project

Dual drive ESC for Clarkson Combat Robotics 1lb freshman PLAnt competition. Supports two 3A brushed drive motors and includes a 5V 1A BEC output to power a receiver.

Dual drive ESC for Clarkson Combat Robotics 1lb freshman PLAnt competition. Supports two 3A brushed drive motors and includes a 5V 1A BEC output to power a receiver.

The ESC implements an STM32C011 MCU to generate PWM for motor drivers from RX channel inputs while monitoring current, signal prescence (failsafe), and battery voltage UVLO.

With the 2026 revision of the ESC, XT30 wire-to-board connectors have been replaced with solder pads for leads to GNB A30 connectors. An XT30 connector is still reccomended for the battery input. The battery shall be a 2S or 3S LiPo battery; 4S is not…

Brushed dual esc, from the project README
From the project README

Main components on the Brushed dual esc

AZ1117CR-5.0TRG1TLV77133PDBVRSTM32C011F6U6DRV8231ADDAR

Brushed dual esc bill of materials (BOM)

21 components, 13 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
AZ1117CR-5.0TRG1
U1
1
TLV77133PDBVR
U2
1
STM32C011F6U6
U3
2
DRV8231ADDAR
U6, U7
1
LC19DJECT-2MA-U1
D2
1
GRM21BR61E106MA73L
10u 25V
C1
3
GMC10X5R475K10NT
4.7u 10V
C2, C4, C5
1
GRM188R61A226ME15D
22u 10V
C3
3
885012206095R
100n 50V
C6, C8, C9
2
A768EB107M1ELAS036
100uF 25V
C10, C11
1
RT0603FRE1033KL
33k
R2
1
RNCP0603FTD10K0
10k
R3
3
RNCP0603FTD750R
750
R4, R5, R6

Brushed dual esc design files

The KiCad project lives in the sigmondkukla/brushed-dual-esc repository on GitHub; these links point at the commit this page was built from.

Brushed dual esc: common questions

What microcontroller does the Brushed dual esc use?

The Brushed dual esc is built around the STM32C011F6U6, from the STM32 family.

How big is the Brushed dual esc PCB?

The Brushed dual esc measures 30 × 25 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Brushed dual esc?

21 components, from 13 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the Brushed dual esc design files?

From the sigmondkukla/brushed-dual-esc repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the Brushed dual esc design in my own project?

The repository has no license, so all rights stay with sigmondkukla. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the Brushed dual esc without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.

Similar boards