Sem motor controller
SWORT-Aerospace·sem-motor-controller·hardware/kicad/08_mcu_debug.kicad_sch
About the Sem motor controller PCB
Sem motor controller is an open source STM32 PCB design by SWORT-Aerospace, published on GitHub. It is a board, with 30 components from 21 distinct parts.
Its main chip is the STM32G474VET6, from the STM32 family. Other key parts include the MAX6369KA+T. By type, the board carries 12 capacitors, 5 resistors, 3 test points, 3 diodes, 2 ICs and 2 connectors.
It belongs with the robotics & motion and power & battery designs in this gallery.
From the project
Telemetry based motocontroller
Purpose-built, telemetry-informed motor controller for a Shell Eco-marathon battery-electric vehicle: power-stage planning, controller firmware core, CAN contract, supervisory energy strategy, and a CSIA vehicle consistency monitor in shadow mode.
Passing host tests does not mean the controller is complete or safe to install.
A hardware-enabled build (-DSEMMCHARDWAREBUILD=ON) refuses to configure until the hardware config validates, and there is no STM32 platform layer yet.
Main components on the Sem motor controller
Sem motor controller bill of materials (BOM)
30 components, 21 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | STM32G474VET6 | U801 | |
| 1 | MAX6369KA+T MAX6369 (candidate) | U802 | |
| 1 | HSE UNSELECTED | Y801 | |
| 1 | SWD | J801 | |
| 1 | UART (bench) | J802 | |
| 1 | RESET | SW801 | |
| 1 | +3V3 | TP801 | |
| 1 | NRST | TP802 | |
| 1 | DRV_NFAULT | TP803 | |
| 1 | green | D801 | |
| 1 | red | D802 | |
| 1 | BAT54 | D803 | |
| 1 | 600R@100MHz | FB801 | |
| 6 | 100nF | C801, C802, C803, C804, C805, C810 | |
| 1 | 4.7uF | C806 | |
| 2 | 1uF | C807, C809 | |
| 1 | 10nF | C808 | |
| 2 | UNRESOLVED load | C811, C812 | |
| 2 | 10k | R801, R804 | |
| 2 | 1k | R802, R803 |
Show 1 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | 0R | R805 |
Sem motor controller design files
The KiCad project lives in the SWORT-Aerospace/sem-motor-controller repository on GitHub; these links point at the commit this page was built from.
Sem motor controller: common questions
What microcontroller does the Sem motor controller use?
The Sem motor controller is built around the STM32G474VET6, from the STM32 family.
How many components are on the Sem motor controller?
30 components, from 21 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Sem motor controller design files?
From the SWORT-Aerospace/sem-motor-controller repository on GitHub, which has the schematic, a netlist and the BOM; the links under Design files point to each one.
Can I use the Sem motor controller design in my own project?
The repository has no license, so all rights stay with SWORT-Aerospace. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Sem motor controller without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.
Similar boards
STM32
LumenPnP Motherboard
opulo-inc
149 × 95 mm296 parts4LCC-BY-SA-4.03.7kSTM32
Type g
google
169 × 30 mm24 parts2LApache-2.02.9kSTM32
Base
google
52.3 × 52.3 mm36 parts2LApache-2.02.9kSTM32
Main panel
google
234 × 84 mm26 parts4LApache-2.02.9kSTM32
Type a
google
150 × 30 mm14 parts2LApache-2.02.9kSTM32
Type c
google
188 × 30 mm17 parts2LApache-2.02.9k