Nexus drive
varunsunkara15·Nexus_drive·hardware/stm32g474.kicad_sch
About the Nexus drive PCB
Nexus drive is an open source STM32 PCB design by varunsunkara15, published on GitHub. It is a board, with 19 components from 10 distinct parts.
Its main chip is the STM32G474METx, from the STM32 family. By type, the board carries 13 capacitors, 2 connectors, 1 IC, 1 crystal, 1 inductor and 1 resistor.
It belongs with the robotics & motion, power & battery and test & measurement designs in this gallery.
From the project
motor gang
Nexus Drive is an open-hardware motor driver we are designing for a humanoid robot's joints.
The goal is a compact board that can sit near each joint actuator and drive its motor accurately and efficiently. It should also report back to the robot's main controller.
Folders for fabrication outputs (Gerbers, BOM, pick-and-place) and datasheets will be added as the design matures.
Main components on the Nexus drive
Nexus drive bill of materials (BOM)
19 components, 10 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | STM32G474METx | LQFP-80_12x12mm_P0.5mm | U1 |
| 1 | ABM8-16.000MHZ-10-1-U-T 16MHz | Y1 | |
| 1 | Conn_01x03 | J1 | |
| 1 | Conn_01x05_Pin | PinHeader_1x05_P1.27mm_Vertical | J2 |
| 1 | 600 Ohm @ 100MHz (0603) | FB1 | |
| 2 | 12pF | C1, C3 | |
| 8 | 100nF | C2, C4, C5, C6, C7, C8, C9, C13 | |
| 2 | 4.7uF | C10, C12 | |
| 1 | 1uF | C11 | |
| 1 | 10k | R1 |
Nexus drive design files
The KiCad project lives in the varunsunkara15/Nexus_drive repository on GitHub; these links point at the commit this page was built from.
- Schematichardware/stm32g474.kicad_sch
Nexus drive: common questions
What microcontroller does the Nexus drive use?
The Nexus drive is built around the STM32G474METx, from the STM32 family.
How many components are on the Nexus drive?
19 components, from 10 distinct parts. The full bill of materials is listed on this page.
Where can I download the Nexus drive design files?
From the varunsunkara15/Nexus_drive repository on GitHub, which has the schematic; the links under Design files point to each one.
Can I use the Nexus drive design in my own project?
The repository has no license, so all rights stay with varunsunkara15. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Nexus drive without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.
Similar boards
STM32
LumenPnP Motherboard
opulo-inc
149 × 95 mm296 parts4LCC-BY-SA-4.03.7kSTM32
Type g
google
169 × 30 mm24 parts2LApache-2.02.9kSTM32
Base
google
52.3 × 52.3 mm36 parts2LApache-2.02.9kSTM32
Main panel
google
234 × 84 mm26 parts4LApache-2.02.9kSTM32
Type a
google
150 × 30 mm14 parts2LApache-2.02.9kSTM32
Type c
google
188 × 30 mm17 parts2LApache-2.02.9k