Device-AngleIndicator
xsuz·Device-AngleIndicator·circuit/AngleIndicator/AngleIndicator.kicad_pcb
About the Device-AngleIndicator PCB
Device-AngleIndicator is an open source STM32 PCB design by xsuz, published on GitHub. It is a 2-layer board measuring 20 × 50 mm, with 19 components from 12 distinct parts.
Its main chip is the STM32G441KBTx, from the STM32 family. By type, the board carries 6 capacitors, 6 resistors, 4 ICs, 2 connectors and 1 diode.
From the project
舵角計および風見
Main components on the Device-AngleIndicator
Device-AngleIndicator bill of materials (BOM)
19 components, 12 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ~ | SOT95P280X130-5N | U1 |
| 1 | STM32G441KBTx | LQFP-32_7x7mm_P0.8mm | U2 |
| 1 | ~ | SOT-23-8_Handsoldering | U3 |
| 1 | ~ | SOIC-8_3.9x4.9mm_P1.27mm | U4 |
| 1 | Conn_01x06 | JST_ZH_B6B-ZR_1x06_P1.50mm_Vertical | J1 |
| 1 | Conn_01x04 | JST_PH_S4B-PH-K_1x04_P2.00mm_Horizontal | J2 |
| 1 | LED | D_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D1 |
| 5 | 0.1u | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C1, C2, C3, C4, C6 |
| 1 | 1.0u | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C5 |
| 2 | 10k | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R1, R6 |
| 3 | 100 | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R2, R3, R4 |
| 1 | 120 | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R5 |
Device-AngleIndicator design files
The KiCad project lives in the xsuz/Device-AngleIndicator repository on GitHub; these links point at the commit this page was built from.
Device-AngleIndicator: common questions
What microcontroller does the Device-AngleIndicator use?
The Device-AngleIndicator is built around the STM32G441KBTx, from the STM32 family.
How big is the Device-AngleIndicator PCB?
The Device-AngleIndicator measures 20 × 50 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Device-AngleIndicator?
19 components, from 12 distinct parts. The full bill of materials is listed on this page.
Where can I download the Device-AngleIndicator design files?
From the xsuz/Device-AngleIndicator repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Device-AngleIndicator design in my own project?
The repository has no license, so all rights stay with xsuz. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Device-AngleIndicator without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.
Similar boards
STM32
LumenPnP Motherboard
opulo-inc
149 × 95 mm296 parts4LCC-BY-SA-4.03.7kSTM32
Type g
google
169 × 30 mm24 parts2LApache-2.02.9kSTM32
Main panel
google
234 × 84 mm26 parts4LApache-2.02.9kSTM32
Base
google
52.3 × 52.3 mm36 parts2LApache-2.02.9kSTM32
Type a
google
150 × 30 mm14 parts2LApache-2.02.9kSTM32
Type c
google
188 × 30 mm17 parts2LApache-2.02.9k