Fipper Zero

aaakum4·Sorta-Flipper-Zero·PCB/Fipper Zero.kicad_pcb

Fipper Zero PCB layout, top view — open source STM32 board by aaakum4

About the Fipper Zero PCB

Fipper Zero is an open source STM32 PCB design by aaakum4, published on GitHub under the GPL-3.0 license. It is a 4-layer board measuring 126 × 70 mm, with 70 components from 36 distinct parts.

Its main chip is the ATMEGA328P-PU, from the STM32 family. By type, the board carries 23 resistors, 16 connectors, 8 capacitors, 7 switches, 1 IC and 1 buzzer.

It belongs with the rf & radio and iot & wireless designs in this gallery.

From the project

At the cost of a flipper zero, I thought that I may never own one. Then I found a hackster.io page that went through a full DIY and cheap Flipper Zero and I thought I'd try it myself with some changes.

At the cost of a flipper zero, I thought that I may never own one. Then I found a hackster.io page that went through a full DIY and cheap Flipper Zero and I thought I'd try it myself with some changes. With this project, I should also learn a ton about PCB's and how electronics work.

V1 is a modular based project to ensure that it will work as planned, then, , I will completely custom make it for V2.

Fipper Zero, from the project README
From the project README

Main components on the Fipper Zero

Fipper Zero bill of materials (BOM)

70 components, 36 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
ATMEGA328P-PU
STM32WB5MMGH6TR
U1
1
CN5
J1
1
CN6
J2
1
CN9
J3
1
CN8
J4
1
Conn_02x04_Odd_Even
J5
1
iButton Connector
J6
1
MicroSD Card
J7
1
Switch
J8
1
Vibration module
J9
2
Conn_01x05
J10, J13
1
Conn_01x02
J11
1
Conn_01x03
J12
1
Conn_01x13
J14
1
Conn_01x18
J15
1
Conn_Coaxial
J16
1
Buzzer
BZ1
3
10u
CP1, CP2, CP3
1
IR Transmitter
IR1
1
IR Receiver
IR2
Show 16 more
QtyPartRefs
3
5.1k
RP1, RU1, RU2
2
47
RX1, RX2
1
K2-1102DP-C4SW-04
SW_Push
SW1
6
SW_Push
SW2, SW3, SW4, SW5, SW6, SW7
2
AP2112K-3.3
UP1, UP2
1
670688000
USB_C_Receptacle_USB2.0_16P
USB1
1
D_Schottky
D1
1
100UF
100nF
C1
1
1uF
C2
5
100nF
C3, C4, C5, C6, C7
1
4.7uF
C8
18
47
R1, R2, R3, R4, R7, R8, R9, R10 +10
2
15K
47
R5, R6
1
5.1k
R18
1
10
R22
1
0
R23

Fipper Zero design files

The KiCad project lives in the aaakum4/Sorta-Flipper-Zero repository on GitHub; these links point at the commit this page was built from.

Fipper Zero: common questions

What microcontroller does the Fipper Zero use?

The Fipper Zero is built around the ATMEGA328P-PU, from the STM32 family.

How big is the Fipper Zero PCB?

The Fipper Zero measures 126 × 70 mm, has 4 copper layers and is 1.6 mm thick.

How many components are on the Fipper Zero?

70 components, from 36 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the Fipper Zero design files?

From the aaakum4/Sorta-Flipper-Zero repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the Fipper Zero design in my own project?

Yes, under the terms of its GPL-3.0 license, which aaakum4 chose for the repository.

Can I test firmware for the Fipper Zero without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.

Similar boards