Blackmagicprobe
acalinp·CANopener·Hardware/black-magic-probe-debugger/blackmagicprobe/blackmagicprobe.kicad_pcb
About the Blackmagicprobe PCB
Blackmagicprobe is an open source STM32 PCB design by acalinp, published on GitHub under the GPL-3.0 license. It is a 2-layer board measuring 16.3 × 39.5 mm, with 29 components from 17 distinct parts.
Its main chip is the STM32F072CBTx, from the STM32 family. Other key parts include the SC662K. By type, the board carries 9 capacitors, 9 resistors, 4 diodes, 2 ICs, 2 connectors and 2 switches.
From the project
WIP
Main components on the Blackmagicprobe
Blackmagicprobe bill of materials (BOM)
29 components, 17 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | SC662K | SOT-23_Handsoldering | U1 |
| 1 | STM32F072CBTx | LQFP-48_7x7mm_Pitch0.5mm | U2 |
| 1 | 8MHz | Crystal_SMD_5032-2pin_5.0x3.2mm | Y1 |
| 1 | USB_B_Micro | USB_Micro-B_Wuerth-629105150521 | J1 |
| 1 | SWD | Pin_Header_Angled_1x04_Pitch2.54mm | J2 |
| 2 | SW_SPST | SW_SPST_B3U-3000P-B | SW1, SW2 |
| 1 | Green | LED_0603 | D1 |
| 1 | Red | LED_0603 | D2 |
| 1 | Orange | LED_0603 | D3 |
| 1 | Yellow | LED_0603 | D4 |
| 3 | 22uF | C_0805 | C1, C4, C9 |
| 4 | 100n | C_0603 | C2, C3, C7, C8 |
| 2 | 22pF | C_0603 | C5, C6 |
| 1 | 1.5k | R_0603 | R1 |
| 2 | 10k | R_0603 | R2, R3 |
| 2 | 22 | R_0603 | R4, R5 |
| 4 | 330 | R_0603 | R6, R7, R8, R9 |
Blackmagicprobe design files
The KiCad project lives in the acalinp/CANopener repository on GitHub; these links point at the commit this page was built from.
Blackmagicprobe: common questions
What microcontroller does the Blackmagicprobe use?
The Blackmagicprobe is built around the STM32F072CBTx, from the STM32 family.
How big is the Blackmagicprobe PCB?
The Blackmagicprobe measures 16.3 × 39.5 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Blackmagicprobe?
29 components, from 17 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Blackmagicprobe design files?
From the acalinp/CANopener repository on GitHub, which has the KiCad layout and the BOM; the links under Design files point to each one.
Can I use the Blackmagicprobe design in my own project?
Yes, under the terms of its GPL-3.0 license, which acalinp chose for the repository.
Can I test firmware for the Blackmagicprobe without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.
More boards in CANopener
Similar boards
STM32
LumenPnP Motherboard
opulo-inc
149 × 95 mm296 parts4LCC-BY-SA-4.03.7kSTM32
Type g
google
169 × 30 mm24 parts2LApache-2.02.9kSTM32
Main panel
google
234 × 84 mm26 parts4LApache-2.02.9kSTM32
Base
google
52.3 × 52.3 mm36 parts2LApache-2.02.9kSTM32
Type a
google
150 × 30 mm14 parts2LApache-2.02.9kSTM32
Type c
google
188 × 30 mm17 parts2LApache-2.02.9k