FanController
aleksul·FanController·hardware/fan-controller.kicad_pcb
About the FanController PCB
FanController is an open source STM32 PCB design by aleksul, published on GitHub under the MIT license. It is a 2-layer board measuring 35.2 × 68 mm, with 50 components from 20 distinct parts.
Its main chip is the STM32F042G6Ux, from the STM32 family. Other key parts include the 74LVC2G32, 350211-1, AMS1117-3.3 and 74HC595. By type, the board carries 15 resistors, 10 capacitors, 8 connectors, 7 ICs, 6 transistors and 2 diodes.
From the project
OpenSource fan controller for your PC
Main components on the FanController
FanController bill of materials (BOM)
50 components, 20 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 3 | 74LVC2G32 | VSSOP-8_2.3x2mm_P0.5mm | U1, U3, U5 |
| 1 | STM32F042G6Ux | QFN-28_4x4mm_P0.5mm | U2 |
| 1 | 350211-1 | 350211-1 | U4 |
| 1 | AMS1117-3.3 | SOT-223-3_TabPin2 | U6 |
| 1 | 74HC595 | SOIC-16_3.9x9.9mm_P1.27mm | U7 |
| 6 | IRLML6244 | SOT-23_Handsoldering | Q1, Q2, Q3, Q4, Q5, Q6 |
| 1 | 16MHz | Crystal_SMD_2520-4Pin_2.5x2.0mm | Y1 |
| 1 | PROG_CONN | PinHeader_1x04_P2.54mm_Vertical | J1 |
| 6 | 47053-1000 | 470531000 | J2, J3, J4, J5, J7, J8 |
| 1 | USB_B_Micro | USB_Micro-B_Molex-105017-0001 | J6 |
| 1 | Reset | SW_TS-1187A-B-A-B | SW1 |
| 1 | LED | LED_1206_3216Metric_Pad1.42x1.75mm_HandSolder | D1 |
| 1 | BAT54CL | SOT-23_Handsoldering | D2 |
| 6 | 100nF | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C1, C2, C3, C4, C7, C10 |
| 2 | TBD | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C5, C6 |
| 1 | 10uF | C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C8 |
| 1 | 22uF | C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C9 |
| 13 | 10K | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1, R2, R3, R4, R5, R6, R7, R8 +5 |
| 1 | 200R | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R12 |
| 1 | 330R | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R15 |
FanController design files
The KiCad project lives in the aleksul/FanController repository on GitHub; these links point at the commit this page was built from.
FanController: common questions
What microcontroller does the FanController use?
The FanController is built around the STM32F042G6Ux, from the STM32 family.
How big is the FanController PCB?
The FanController measures 35.2 × 68 mm, has 2 copper layers and is 1.6002 mm thick.
How many components are on the FanController?
50 components, from 20 distinct parts. The full bill of materials is listed on this page.
Where can I download the FanController design files?
From the aleksul/FanController repository on GitHub, which has the KiCad layout; the links under Design files point to each one.
Can I use the FanController design in my own project?
Yes, under the terms of its MIT license, which aleksul chose for the repository.
Can I test firmware for the FanController without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.
Similar boards
STM32
LumenPnP Motherboard
opulo-inc
149 × 95 mm296 parts4LCC-BY-SA-4.03.7kSTM32
Type g
google
169 × 30 mm24 parts2LApache-2.02.9kSTM32
Main panel
google
234 × 84 mm26 parts4LApache-2.02.9kSTM32
Base
google
52.3 × 52.3 mm36 parts2LApache-2.02.9kSTM32
Type a
google
150 × 30 mm14 parts2LApache-2.02.9kSTM32
Type c
google
188 × 30 mm17 parts2LApache-2.02.9k