Duplexer 145 435 BNC 25W REV A
anatolbricoham·antenaSatCommrotor·PortableSatLite/hardware/diplexer/Duplexer_145_435_BNC_25W_REV_A/Duplexer_145_435_BNC_25W_REV_A.kicad_pcb
About the Duplexer 145 435 BNC 25W REV A PCB
Duplexer 145 435 BNC 25W REV A is an open source PCB design by anatolbricoham, published on GitHub. It is a 2-layer board measuring 80 × 60 mm, with 13 components from 13 distinct parts.
By type, the board carries 5 inductors, 5 capacitors and 3 connectors.
From the project
DUPLEXER 145 / 435 MHz — BNC — 25 W TARGET — REV A
DUPLEXER 145 / 435 MHz — BNC — 25 W TARGET — REV A
Architecture J1 ANT -> 5th-order Chebyshev LPF -> J2 VHF J1 ANT -> 5th-order Chebyshev HPF -> J3 UHF
Filter values are based on the published KI0AG 2m/70cm micro-duplexer: LPF: 68 nH, 18 pF, 100 nH, 18 pF, 68 nH HPF: 4.7 pF, 16 nH, 3.1 pF, 16 nH, 4.7 pF
Target bands: VHF: 144–146 MHz, nominal 145 MHz UHF: 430–440 MHz, nominal 435 MHz System impedance: 50 ohm Power target: 25 W
Duplexer 145 435 BNC 25W REV A bill of materials (BOM)
13 components, 13 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | BNC ANT 50R | J1 | J1 |
| 1 | BNC VHF 50R | J2 | J2 |
| 1 | BNC UHF 50R | J3 | J3 |
| 1 | 68nH | L1 | L1 |
| 1 | 100nH | L2 | L2 |
| 1 | 68nH | L3 | L3 |
| 1 | 16nH | L4 | L4 |
| 1 | 16nH | L5 | L5 |
| 1 | 18pF | C1 | C1 |
| 1 | 18pF | C2 | C2 |
| 1 | 4.7pF | C3 | C3 |
| 1 | 3.1pF | C4 | C4 |
| 1 | 4.7pF | C5 | C5 |
Duplexer 145 435 BNC 25W REV A design files
The KiCad project lives in the anatolbricoham/antenaSatCommrotor repository on GitHub; these links point at the commit this page was built from.
- LayoutPortableSatLite/hardware/diplexer/Duplexer_145_435_BNC_25W_REV_A/Duplexer_145_435_BNC_25W_REV_A.kicad_pcb
- SchematicPortableSatLite/hardware/diplexer/Duplexer_145_435_BNC_25W_REV_A/Duplexer_145_435_BNC_25W_REV_A.kicad_sch
- BOMPortableSatLite/hardware/diplexer/Duplexer_145_435_BNC_25W_REV_A/documentation/BOM.csv
Duplexer 145 435 BNC 25W REV A: common questions
How big is the Duplexer 145 435 BNC 25W REV A PCB?
The Duplexer 145 435 BNC 25W REV A measures 80 × 60 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Duplexer 145 435 BNC 25W REV A?
13 components, from 13 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Duplexer 145 435 BNC 25W REV A design files?
From the anatolbricoham/antenaSatCommrotor repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Duplexer 145 435 BNC 25W REV A design in my own project?
The repository has no license, so all rights stay with anatolbricoham. Use it as a reference, and ask the author before reusing the design.