PortableSatCarrier
anatolbricoham·antenaSatCommrotor·hardware/PortableSatCarrier.kicad_pcb
About the PortableSatCarrier PCB
PortableSatCarrier is an open source ESP32 PCB design by anatolbricoham, published on GitHub. It is a 2-layer board measuring 180 × 130 mm, with 40 components from 40 distinct parts.
Its main chip is the AP2112K-3.3TRG1, from the ESP32 family. Other key parts include the MCP23017-E/SO and TCA9548APWR. By type, the board carries 13 connectors, 10 resistors, 5 capacitors, 4 fuses, 3 ICs and 2 diodes.
From the project
La documentacion se prepara en espanol, ingles y hungaro. Las ediciones inglesa y hungara estan en traduccion/sincronizacion y no se consideran completas hasta comprobar cobertura y correspondencia con la revision tecnica vigente. El indice de idiomas se enlazara al finalizar esa
La documentacion se prepara en espanol, ingles y hungaro. Las ediciones inglesa y hungara estan en traduccion/sincronizacion y no se consideran completas hasta comprobar cobertura y correspondencia con la revision tecnica vigente. El indice de idiomas se enlazara al finalizar esas pruebas. Los textos originales de licencias de terceros se conservan sin alteracion.
Main components on the PortableSatCarrier
PortableSatCarrier bill of materials (BOM)
40 components, 40 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | AP2112K-3.3TRG1 ESP32_DEVKITC_V4_38_WROOM32E | U1_module | U1 |
| 1 | MCP23017-E/SO WATTEROTT_TMC2209_V2 | U2_driver | U2 |
| 1 | TCA9548APWR WATTEROTT_TMC2209_V2 | U3_driver | U3 |
| 1 | DC_IN_12V | J1_terminal | J1 |
| 1 | LATCHED_STOP_POWER_OUT_RETURN | J2_terminal | J2 |
| 1 | STOP_N_NC_AUX_ONLY | J3_xh | J3 |
| 1 | EXTERNAL_BUCK_INPUT | J4_terminal | J4 |
| 1 | EXTERNAL_BUCK_5V_RETURN | J5_terminal | J5 |
| 1 | GNSS_3V3_UART | J6_xh | J6 |
| 1 | AZ_AS5600_I2C0 | J7_xh | J7 |
| 1 | EL_AS5600_I2C1 | J8_xh | J8 |
| 1 | OPTIONAL_IMU_MAG_I2C0 | J9_xh | J9 |
| 1 | AZ_MIN_N_NC_AUX_ONLY | J10_xh | J10 |
| 1 | AZ_MAX_N_NC_AUX_ONLY | J11_xh | J11 |
| 1 | EL_MIN_N_NC_AUX_ONLY | J12_xh | J12 |
| 1 | EL_MAX_N_NC_AUX_ONLY | J13_xh | J13 |
| 1 | T3.15A_MAIN | F1_fuse | F1 |
| 1 | T2.5A_MOTOR | F2_fuse | F2 |
| 1 | T1A_LOGIC_5V | F3_fuse | F3 |
| 1 | T1A_BUCK_INPUT | F4_fuse | F4 |
Show 20 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | AZ_MOTOR | JM1_terminal | JM1 |
| 1 | EL_MOTOR | JM2_terminal | JM2 |
| 1 | REMOVE_FOR_USB | JP1_header | JP1 |
| 1 | SB560_REVERSE_BLOCK | D1_diode | D1 |
| 1 | SMBJ15A_TVS | D2_tvs | D2 |
| 1 | GRM188R71C105KA12D 220u_35V_LOW_ESR | C1_capacitor | C1 |
| 1 | GRM188R71C105KA12D 220u_35V_LOW_ESR | C2_capacitor | C2 |
| 1 | GRM188R71C104KA01D 100n_50V | C3_capacitor | C3 |
| 1 | GRM188R71C104KA01D 100n_50V | C4_capacitor | C4 |
| 1 | GRM188R71C104KA01D 100n_50V | C5_capacitor | C5 |
| 1 | RC0603FR-074K7L 10k | R1_resistor | R1 |
| 1 | RC0603FR-074K7L 10k | R2_resistor | R2 |
| 1 | RC0603FR-0710KL 10k | R3_resistor | R3 |
| 1 | RC0603FR-074K7L 10k | R4_resistor | R4 |
| 1 | RC0603FR-074K7L 10k | R5_resistor | R5 |
| 1 | RC0603FR-074K7L 10k | R6_resistor | R6 |
| 1 | RC0603FR-074K7L 4k7 | R7_resistor | R7 |
| 1 | RC0603FR-074K7L 4k7 | R8_resistor | R8 |
| 1 | RC0603FR-074K7L 4k7 | R9_resistor | R9 |
| 1 | RC0603FR-074K7L 4k7 | R10_resistor | R10 |
PortableSatCarrier design files
The KiCad project lives in the anatolbricoham/antenaSatCommrotor repository on GitHub; these links point at the commit this page was built from.
PortableSatCarrier: common questions
What microcontroller does the PortableSatCarrier use?
The PortableSatCarrier is built around the AP2112K-3.3TRG1, from the ESP32 family.
How big is the PortableSatCarrier PCB?
The PortableSatCarrier measures 180 × 130 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the PortableSatCarrier?
40 components, from 40 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the PortableSatCarrier design files?
From the anatolbricoham/antenaSatCommrotor repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the PortableSatCarrier design in my own project?
The repository has no license, so all rights stay with anatolbricoham. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the PortableSatCarrier without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
More boards in antenaSatCommrotor
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k