Qspi interposer
About the Qspi interposer PCB
Qspi interposer is an open source PCB design by azonenberg, published on GitHub under the BSD-3-Clause license. It is a 4-layer board measuring 58.5 × 20.5 mm, with 10 components from 7 distinct parts.
Other key parts include the M24C02-RMC6TG. By type, the board carries 4 resistors, 3 capacitors, 2 connectors and 1 IC.
From the project
FPGA based dumper for flashes and more
1.0V shunt resistor is missing a zone fill. Will monitor droop under load and see if we need to add top layer power path. U33 is way too close to J10. Seems to have fit OK, not touching for now, but tough to assemble. INITB and PROGB on FPGA are 1.8V signals but we try to drive with 3.3 from supervisor! Rework: add pull to 1.8V on board, open drain in super firmware JTAG connector VCC is connected to 3.3V. We need to supply 1.8 here. Temporary workaround: six pin extension cable, pass through JTAG + GND and supply 1.8V to dongle externally. Long term fix: interposer board * DONE on FPGA is…
Main components on the Qspi interposer
Qspi interposer bill of materials (BOM)
10 components, 7 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | M24C02-RMC6TG | DFN_8_0.5MM_2x3MM_TALL | U1 |
| 1 | CONN_DUMPTRUCK_DEVICE | CONN_SAMTEC_BSE-040-01-L-D-A-TR | J1 |
| 1 | 103P010BB1100 | CONN_AMPHENOL_103P010BB100 | J2 |
| 1 | 0.47 uF | EIA_0402_CAP_NOSILK | C1 |
| 2 | 4.7 uF | EIA_0603_CAP_NOSILK | C2, C4 |
| 1 | 0 | EIA_0402_RES_NOSILK | R1 |
| 3 | 10K | EIA_0402_RES_NOSILK | R2, R3, R4 |
Qspi interposer design files
The KiCad project lives in the azonenberg/dumptruck repository on GitHub; these links point at the commit this page was built from.
Qspi interposer: common questions
How big is the Qspi interposer PCB?
The Qspi interposer measures 58.5 × 20.5 mm, has 4 copper layers and is 1.6 mm thick.
How many components are on the Qspi interposer?
10 components, from 7 distinct parts. The full bill of materials is listed on this page.
Where can I download the Qspi interposer design files?
From the azonenberg/dumptruck repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Qspi interposer design in my own project?
Yes, under the terms of its BSD-3-Clause license, which azonenberg chose for the repository.
More boards in dumptruck
STM32Main
130 × 90 mm435 parts10LBSD-3-Clause17
Ram expansion
40.3 × 21.8 mm24 parts4LBSD-3-Clause17
Pin header
55.5 × 26.5 mm12 parts4LBSD-3-Clause17
Qspi mitm
41 × 20.5 mm12 parts4LBSD-3-Clause17
Parallel nor csp56
57 × 31 mm10 parts4LBSD-3-Clause17
Dfn8-small qspi
52.5 × 20.5 mm10 parts4LBSD-3-Clause17
Soic8-wide
52.5 × 20.5 mm10 parts4LBSD-3-Clause17
Jtag interposer
20 × 31 mm5 parts4LBSD-3-Clause17