ISA-26-TESTER-KIT-COMMUNITY
About the ISA-26-TESTER-KIT-COMMUNITY PCB
ISA-26-TESTER-KIT-COMMUNITY is an open source AVR/Arduino PCB design by bottlecoder-raj, published on GitHub. It is a 2-layer board measuring 225.3 × 126.5 mm, with 30 components from 20 distinct parts.
Its main chip is the Arduino_Nano_v2.x, from the AVR/Arduino family. By type, the board carries 27 connectors, 1 module and 1 buzzer.
Main components on the ISA-26-TESTER-KIT-COMMUNITY
ISA-26-TESTER-KIT-COMMUNITY bill of materials (BOM)
30 components, 20 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | Arduino_Nano_v2.x | Arduino_Nano | A1 |
| 1 | RFID | PinHeader_1x08_P2.54mm_Vertical | J1 |
| 1 | I2C 16X2 | PinHeader_1x04_P2.54mm_Vertical | J2 |
| 1 | TX/RX | PinHeader_1x04_P2.54mm_Vertical | J3 |
| 11 | Conn_01x01_Pin | PinHeader_1x01_P2.54mm_Vertical | J4, J18, J19, J20, J21, J22, J23, J24 +3 |
| 1 | Servo | PinSocket_1x03_P2.54mm_Vertical | J5 |
| 1 | Ultrasonic sensor | PinSocket_1x04_P2.54mm_Vertical | J6 |
| 1 | DHT11 | PinSocket_1x03_P2.54mm_Vertical | J7 |
| 1 | TEST_PIN | PinSocket_1x02_P2.54mm_Vertical | J8 |
| 1 | 0.96" Oled | PinSocket_1x04_P2.54mm_Vertical | J9 |
| 1 | LDR/IR | PinSocket_1x03_P2.54mm_Vertical | J10 |
| 1 | GAS | PinSocket_1x04_P2.54mm_Vertical | J11 |
| 1 | PIR | PinSocket_1x03_P2.54mm_Vertical | J12 |
| 1 | Hall Effect | PinSocket_1x03_P2.54mm_Vertical | J13 |
| 1 | MPU6050 | PinSocket_1x08_P2.54mm_Vertical | J14 |
| 1 | 4x4 Keypad | PinSocket_1x08_P2.54mm_Vertical | J15 |
| 1 | Joystick | PinSocket_1x05_P2.54mm_Vertical | J16 |
| 1 | MOTOR | TerminalBlock_Phoenix_MKDS-1,5-2-5.08_1x02_P5.08mm_Horizontal | J17 |
| 1 | Buzzer | TerminalBlock_Phoenix_MKDS-1,5-2-5.08_1x02_P5.08mm_Horizontal | BZ1 |
| 1 | 3V3/5V | PinSocket_1x03_P2.54mm_Vertical | POWER_PLUG1 |
ISA-26-TESTER-KIT-COMMUNITY design files
The KiCad project lives in the bottlecoder-raj/ISA-26-TESTER-KIT-COMMUNITY repository on GitHub; these links point at the commit this page was built from.
- LayoutA4/A4.kicad_pcb
- SchematicA4/A4.kicad_sch
ISA-26-TESTER-KIT-COMMUNITY: common questions
What microcontroller does the ISA-26-TESTER-KIT-COMMUNITY use?
The ISA-26-TESTER-KIT-COMMUNITY is built around the Arduino_Nano_v2.x, from the AVR/Arduino family.
How big is the ISA-26-TESTER-KIT-COMMUNITY PCB?
The ISA-26-TESTER-KIT-COMMUNITY measures 225.3 × 126.5 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the ISA-26-TESTER-KIT-COMMUNITY?
30 components, from 20 distinct parts. The full bill of materials is listed on this page.
Where can I download the ISA-26-TESTER-KIT-COMMUNITY design files?
From the bottlecoder-raj/ISA-26-TESTER-KIT-COMMUNITY repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the ISA-26-TESTER-KIT-COMMUNITY design in my own project?
The repository has no license, so all rights stay with bottlecoder-raj. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the ISA-26-TESTER-KIT-COMMUNITY without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.
Similar boards
AVR/ArduinoMagspoof
samyk
35 × 29 mm11 parts2LNo license4.2k
AVR/ArduinoRedox keyboard
mattdibi
162.2 × 126.5 mm77 parts2LMIT2.0k
AVR/ArduinoLabrador
espotek-org
36.8 × 34.7 mm75 parts2LNo license1.2k
AVR/ArduinoV4
stuartpittaway
30 × 50 mm38 parts2LCC-BY-NC-4.01.1k
AVR/ArduinoModuleV450
30 × 61.4 mm39 parts2LCC-BY-NC-4.01.1k
AVR/ArduinoDiscipline
coseyfannitutti
304.9 × 122.8 mm170 parts2LCC-BY-NC-4.01.0k