Iobox3
Carputer-project·iobox3pcb
About the Iobox3 PCB
Iobox3 is an open source PCB design by Carputer-project, published on GitHub. It is a 2-layer board measuring 76.7 × 87.6 mm, with 30 components from 23 distinct parts.
Other key parts include the LM2596S-5. By type, the board carries 11 resistors, 7 diodes, 1 IC, 1 buzzer, 1 fuse and 1 inductor.
From the project
KiCad PCB for the MicroSquirt iobox3 - ESP32 DevKit carrier: IAC MOSFET, ULN2003A outputs, protected analog front end, dual round-TFT headers
Two-layer THT board carrying an ESP32 DevKit V1 (38-pin) plus all support circuitry for esp32msiobox3: actuator drivers, protected analog inputs, dual round-TFT headers, and in-car power conditioning. Silk: CARPUTER V5.
Traced from the PCB netlist against the DevKit-V1 symbol and the iobox3 firmware defaults. Everything below matches the running firmware.
- IAC stage: GPIO19 → R2 (populate 120 Ω per bench doctrine) → IRLZ44N gate, R1 = 10 k gate pull-down. Drain → IDLE1-1; D1 1N5404 clamps the valve node to +12VA (flyback recirculation). IDLE1-3 = +12VA valve feed. 250 Hz PWM, valve current…
Main components on the Iobox3
Iobox3 bill of materials (BOM)
30 components, 23 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | LM2596S-5 | TO-262-5_Vertical | U2 |
| 1 | R | TO-39-3 | 2n222 |
| 1 | 12v in | Wago_734-132_1x02_P3.50mm_Vertical | 12vin1 |
| 1 | Buzzer | Buzzer_12x9.5RM7.6 | BZ1 |
| 1 | CAP | CP_Radial_D4.0mm_P2.00mm | CAP1 |
| 1 | 1N5404 | D_DO-201AD_P15.24mm_Horizontal | DIODE1 |
| 1 | Fuse | Fuse_Blade_Mini_directSolder | F1 |
| 1 | IAC | Wago_734-133_1x03_P3.50mm_Vertical | IDLE1 |
| 1 | gnd | Wago_734-133_1x03_P3.50mm_Vertical | gnd1 |
| 1 | IRLZ44N | TO-220-3_Vertical | mosfet1 |
| 1 | ULN2002A | DIL16 | uln1 |
| 1 | 1N5404 | D_DO-201AD_P15.24mm_Horizontal | D1 |
| 3 | D_Zener | D_5W_P10.16mm_Horizontal | D4, D6, D10 |
| 2 | D_Capacitance | CP_Radial_D5.0mm_P2.00mm | D5, D11 |
| 1 | D_Capacitance | D_5W_P10.16mm_Horizontal | D9 |
| 1 | L | L_Axial_L5.3mm_D2.2mm_P7.62mm_Horizontal_Vishay_IM-1 | L1 |
| 2 | R | R_Axial_DIN0204_L3.6mm_D1.6mm_P7.62mm_Horizontal | R1, R2 |
| 1 | 100 | R_Axial_DIN0204_L3.6mm_D1.6mm_P5.08mm_Horizontal | R3 |
| 3 | 4.6 | R_Axial_DIN0204_L3.6mm_D1.6mm_P7.62mm_Horizontal | R4, R6, R8 |
| 2 | 100 | R_Axial_DIN0204_L3.6mm_D1.6mm_P7.62mm_Horizontal | R5, R7 |
Show 3 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | 4.6ohms | R_Axial_DIN0204_L3.6mm_D1.6mm_P7.62mm_Horizontal | R9 |
| 1 | 220ohms | R_Axial_DIN0204_L3.6mm_D1.6mm_P7.62mm_Horizontal | R10 |
| 1 | 1k | R_Axial_DIN0204_L3.6mm_D1.6mm_P5.08mm_Horizontal | R12 |
Iobox3 design files
The KiCad project lives in the Carputer-project/iobox3pcb repository on GitHub; these links point at the commit this page was built from.
- LayoutCARPUTER.kicad_pcb
- SchematicCARPUTER.kicad_sch
Iobox3: common questions
How big is the Iobox3 PCB?
The Iobox3 measures 76.7 × 87.6 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Iobox3?
30 components, from 23 distinct parts. The full bill of materials is listed on this page.
Where can I download the Iobox3 design files?
From the Carputer-project/iobox3pcb repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Iobox3 design in my own project?
The repository has no license, so all rights stay with Carputer-project. Use it as a reference, and ask the author before reusing the design.