HardLabs

Telemetry PCB V2

CohenMurray·SRAD-Telemetry-PCB·PCB/Telemetry PCB V2/Telemetry PCB V2.kicad_pcb

Telemetry PCB V2 layout, top view — open source STM32 board by CohenMurray

About the Telemetry PCB V2

Telemetry PCB V2 is an open source STM32 PCB design by CohenMurray, published on GitHub. It is a 4-layer board measuring 70 × 70 mm, with 50 components from 35 distinct parts.

Its main chip is the STM32F411CEUx, from the STM32 family. Other key parts include the E22-900M33S, MCP1700x-250xxTT and AP62200WU. By type, the board carries 17 capacitors, 11 resistors, 6 connectors, 5 diodes, 4 ICs and 2 crystals.

Main components on the Telemetry PCB V2

E22-900M33SSTM32F411CEUxMCP1700x-250xxTTAP62200WU

Telemetry PCB V2 bill of materials (BOM)

50 components, 35 distinct parts.

QtyPartRefs
1
E22-900M33S
IC1
1
STM32F411CEUx
U1
1
MCP1700x-250xxTT
U2
1
AP62200WU
U3
1
25MHZ 18pF
Y1
1
32.768k 12.5pF
Y2
1
USB_C_Receptacle_USB2.0_16P
J1
1
DBG/PGRM Hdr.
J2
1
DATA IN
J3
1
GPS
J4
1
Battery
J5
1
Conn_01x02
J6
1
BOOT
SW1
1
RESET
SW2
1
GND
TP1
1
+5v
TP2
1
WS2812B
D1
2
5.23V
D2, D3
1
GREEN
D4
1
RED
D5
Show 15 more
QtyPartRefs
1
4.7uH
L1
2
16pF
C1, C5
2
5pF
C2, C3
1
4.7uF
C4
4
0.1uF
C6, C7, C8, C9
3
0.1uF
C10, C12, C17
2
1uF
C13, C14
1
10uF
C15
2
22uF
C16, C18
2
10
R1, R2
2
5.1k
R3, R4
4
10K
R5, R6, R7, R8
1
52.3k
R9
1
1k
R10
1
5.1k
R11

Telemetry PCB V2 design files

The KiCad project lives in the CohenMurray/SRAD-Telemetry-PCB repository on GitHub; these links point at the commit this page was built from.

Telemetry PCB V2: common questions

What microcontroller does the Telemetry PCB V2 use?

The Telemetry PCB V2 is built around the STM32F411CEUx, from the STM32 family.

How big is the Telemetry PCB V2?

The Telemetry PCB V2 measures 70 × 70 mm, has 4 copper layers and is 1.6 mm thick.

How many components are on the Telemetry PCB V2?

50 components, from 35 distinct parts. The full bill of materials is listed on this page.

Where can I download the Telemetry PCB V2 design files?

From the CohenMurray/SRAD-Telemetry-PCB repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.

Can I use the Telemetry PCB V2 design in my own project?

The repository has no license, so all rights stay with CohenMurray. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the Telemetry PCB V2 without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.

More boards in SRAD-Telemetry-PCB

Earlier revisions in the repo: Telemetry PCB

Similar boards