Avtech agv main

eerdemgundogdu·avtech-agv-main·hardware/avtech-agv-carrier/avtech-agv-carrier.kicad_pcb

Avtech agv main PCB layout, top view — open source NXP board by eerdemgundogdu

About the Avtech agv main PCB

Avtech agv main is an open source NXP PCB design by eerdemgundogdu, published on GitHub under the MIT license. It is a 2-layer board measuring 110 × 85 mm, with 76 components from 45 distinct parts.

Its main chip is the PJRC Teensy 4.1 + 2x 1x24 disi header, from the NXP family. Other key parts include the TI LMR16006XDDCR and Diodes AP2112K-3.3TRG1. By type, the board carries 32 resistors, 12 diodes, 11 capacitors, 10 connectors, 5 transistors and 3 ICs.

It belongs with the sensors designs in this gallery.

From the project

2-layer (105x80 mm, FR-4, 1.6 mm, 1 oz Cu) carrier board for the Teensy 4.1 forklift AGV.

2-layer (105x80 mm, FR-4, 1.6 mm, 1 oz Cu) carrier board for the Teensy 4.1 forklift AGV.

- Power input: 1 A fuse, SS16 reverse-polarity diode, SMBJ30CA TVS, 47 uF bulk capacitor. - 24 V to 5 V buck: LMR16006X (60 V, 0.6 A, 700 kHz), 22 uH inductor. - 5 V to 3.3 V LDO: AP2112K-3.3 for sensors; Teensy VIN isolated through a B5819W Schottky diode. - Hardware E-stop: NC button in series with the motor-power contactor coil, plus MOTOREN low-side switch (BCP56-16`) and loop sense divider. - Hoverboard UART: 3-pin connector (15 V pin omitted), 1k series resistors and BAT54S Schottky clamps. -…

Main components on the Avtech agv main

TI LMR16006XDDCRDiodes AP2112K-3.3TRG1PJRC Teensy 4.1 + 2x 1x24 disi header

Avtech agv main bill of materials (BOM)

76 components, 45 distinct parts.

QtyPartRefs
1
TI LMR16006XDDCR
LMR16006XDDCR
U1
1
Diodes AP2112K-3.3TRG1
AP2112K-3.3
U2
1
PJRC Teensy 4.1 + 2x 1x24 disi header
Teensy 4.1
U3
4
AOS AO3400A
AO3400A
Q1, Q2, Q3, Q4
1
Nexperia BCP56-16
BCP56-16
Q5
1
Phoenix 1715721
24V AKU
J1
1
JST B3B-XH-A
HOVERBOARD
J2
1
JST B6B-XH-A
IMU SPI
J3
1
JST B11B-XH-A
QTR-8A
J4
1
JST B4B-XH-A
HC-SR04 ON
J5
1
JST B4B-XH-A
HC-SR04 SOL
J6
1
JST B4B-XH-A
HC-SR04 SAG
J7
1
JST B6B-XH-A
DM556
J8
1
JST B2B-XH-A
E-STOP (NC)
J9
1
JST B2B-XH-A
KONTAKTOR
J10
1
12 mm 5V aktif buzzer
5V aktif
BZ1
1
Littelfuse 0466001.NRHF
1A 63V
F1
3
SS16 (60V 1A)
SS16
D1, D3, D10
1
Littelfuse SMBJ30CA
SMBJ30CA
D2
1
B5819W (40V 1A)
B5819W
D4
Show 25 more
QtyPartRefs
1
0603 yesil LED
YESIL
D5
2
BAT54S
D6, D7
1
1N4148WS
1N4148W
D8
1
0603 mavi LED
MAVI
D9
1
0603 kirmizi LED
KIRMIZI
D11
1
BZT52C3V3
D12
1
Bourns SRN6045TA-220M
22uH
L1
1
Panasonic EEE-FK1J470P
47uF 63V
C1
2
X7R 1210 100V
2.2uF 100V
C2, C3
1
X7R 0603 25V
100nF 25V
C4
2
X7R 1206 10V
22uF 10V
C5, C6
2
X7R 0603 16V
1uF
C7, C8
1
X5R 0805 10V
10uF
C9
2
X7R 0603 16V
100nF
C10, C11
5
0603 100k 1%
100k
R1, R21, R22, R23, R25
1
0603 54.9k 1%
54.9k
R2
4
0603 10k 1%
10k
R3, R28, R29, R31
4
0603 2.2k 1%
2.2k
R4, R12, R14, R16
3
0603 1k 1%
1k
R5, R6, R32
2
0603 33 1%
33
R7, R8
7
0603 100 1%
100
R9, R10, R11, R18, R19, R20, R24
3
0603 3.3k 1%
3.3k
R13, R15, R17
1
0603 330 1%
330
R26
1
0603 470 1%
470
R27
1
0603 47k 1%
47k
R30

Avtech agv main design files

The KiCad project lives in the eerdemgundogdu/avtech-agv-main repository on GitHub; these links point at the commit this page was built from.

Avtech agv main: common questions

What microcontroller does the Avtech agv main use?

The Avtech agv main is built around the PJRC Teensy 4.1 + 2x 1x24 disi header, from the NXP family.

How big is the Avtech agv main PCB?

The Avtech agv main measures 110 × 85 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Avtech agv main?

76 components, from 45 distinct parts. The full bill of materials is listed on this page.

Where can I download the Avtech agv main design files?

From the eerdemgundogdu/avtech-agv-main repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.

Can I use the Avtech agv main design in my own project?

Yes, under the terms of its MIT license, which eerdemgundogdu chose for the repository.

Can I test firmware for the Avtech agv main without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug NXP firmware against it before you order a PCB.

Similar boards