Stm32l010-breakout
About the Stm32l010-breakout
Stm32l010-breakout is an open source STM32 PCB design by elevendroids, published on GitHub under the CC-BY-SA-4.0 license. It is a 2-layer board measuring 24 × 50 mm, with 29 components from 19 distinct parts.
Its main chip is the STM32L010K8Tx, from the STM32 family. By type, the board carries 11 resistors, 8 capacitors, 3 connectors, 2 diodes, 1 IC and 1 transistor.
It belongs with the dev boards & breakouts designs in this gallery.
From the project
STM32L010 Breakout Board
Small MCU board designed primarly for the STM32L010K8T6 ARM Cortex-M0+ microcontroller: Datasheet
Can also be used with other pin-compatible STM32 MCUs in LQFP-32 package: - Most of the STM32L0 family - STM32L4x2 (ARM Cortex-M4)
- minimal subset of components, no power regulation (important when playing with low power apps) - optional LSE crystal, if not used its GPIO pins can be connected to the user header by soldering relevant 0R resistors (see schematic) - two buffered user LEDs, connected to the header - no reserved GPIOs - reset button - standard 0.05" pitch SWD programming header…
Main components on the Stm32l010-breakout
Stm32l010-breakout bill of materials (BOM)
29 components, 19 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | STM32L010K8Tx | LQFP-32_7x7mm_P0.8mm | U1 |
| 1 | BC847CDW1 | SOT-363_SC-70-6 | Q1 |
| 1 | 32.768kHz | Crystal_SMD_3215-2Pin_3.2x1.5mm | Y1 |
| 1 | SWD | PinHeader_2x05_P1.27mm_Vertical_SMD | J1 |
| 1 | Left | PinHeader_1x16_P2.54mm_Vertical | J2 |
| 1 | Right | PinHeader_1x16_P2.54mm_Vertical | J3 |
| 1 | Reset | SW_SPST_CK_RS282G05A3 | SW1 |
| 1 | LED0 | LED_0805_2012Metric | D1 |
| 1 | LED1 | LED_0805_2012Metric | D2 |
| 1 | Bead | L_0603_1608Metric | FB1 |
| 1 | 10u | C_0805_2012Metric | C1 |
| 4 | 100n | C_0603_1608Metric | C2, C3, C5, C8 |
| 1 | 1u | C_0603_1608Metric | C4 |
| 2 | 12p* | C_0603_1608Metric | C6, C7 |
| 2 | 47k | R_0603_1608Metric | R1, R4 |
| 2 | 100k | R_0603_1608Metric | R2, R5 |
| 2 | 330R | R_0603_1608Metric | R3, R6 |
| 1 | 10k | R_0603_1608Metric | R7 |
| 4 | 0R | R_0603_1608Metric | R8, R9, R10, R11 |
Stm32l010-breakout design files
The KiCad project lives in the elevendroids/stm32l010-breakout repository on GitHub; these links point at the commit this page was built from.
Stm32l010-breakout: common questions
What microcontroller does the Stm32l010-breakout use?
The Stm32l010-breakout is built around the STM32L010K8Tx, from the STM32 family.
How big is the Stm32l010-breakout?
The Stm32l010-breakout measures 24 × 50 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Stm32l010-breakout?
29 components, from 19 distinct parts. The full bill of materials is listed on this page.
Where can I download the Stm32l010-breakout design files?
From the elevendroids/stm32l010-breakout repository on GitHub, which has the KiCad layout; the links under Design files point to each one.
Can I use the Stm32l010-breakout design in my own project?
Yes, under the terms of its CC-BY-SA-4.0 license, which elevendroids chose for the repository.
Can I test firmware for the Stm32l010-breakout without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.
Similar boards
STM32LumenPnP Motherboard
opulo-inc
149 × 95 mm296 parts4LCC-BY-SA-4.03.7k
STM32AxxSolder
AxxAxx
39 × 82.5 mm122 parts2LGPL-3.01.7k
STM32AIOC
skuep
21 × 31.5 mm47 parts2LMIT1.4k
STM32Ferris
pierrechevalier83
208.8 × 86.8 mm102 parts2LSHL-2.11.3k
STM32176 pin board
rusefi
61.8 × 73.2 mm76 parts2LGPL-3.01.2k
STM32Brain board STM32F407
61.8 × 73.2 mm69 parts2LGPL-3.01.2k