DeathClock

EmileBV·DeathClock·PCB/DeathClock/DeathClock.kicad_pcb

DeathClock PCB layout, top view — open source STM32 board by EmileBV

About the DeathClock PCB

DeathClock is an open source STM32 PCB design by EmileBV, published on GitHub. It is a 2-layer board measuring 37.2 × 31.2 mm, with 31 components from 20 distinct parts.

Its main chip is the STM32L010F4P6, from the STM32 family. By type, the board carries 16 capacitors, 4 resistors, 3 diodes, 2 transistors, 2 connectors and 1 IC.

It belongs with the displays & leds designs in this gallery.

From the project

This project's goal to make a pocket "watch" that will last and run as long as possible and count down to a set date/time. Using an E-Paper display that will be updated maybe twice per day and a STM32L010xx MCU running on its internal low power clock to achieve very long runtime

This project's goal to make a pocket "watch" that will last and run as long as possible and count down to a set date/time. Using an E-Paper display that will be updated maybe twice per day and a STM32L010xx MCU running on its internal low power clock to achieve very long runtime on a CR2430 coin cell.

This project is still in its very early stages right now, don't expect too much.

DeathClock, from the project README
From the project README

Main components on the DeathClock

DeathClock bill of materials (BOM)

31 components, 20 distinct parts.

QtyPartRefs
1
STM32L010F4P6
U1
1
PJA3431_R1_00001
Q1
1
PJA3430_R1_00001
Q2
1
Crystal
Y1
1
Conn_01x05_Female
J1
1
EDP_24pin_conn FFC2B35-24-T
J2
1
AdamTech_CR2430_BH-109B-5
BAT1
3
SS2040FL
D1, D2, D3
1
10uH ±20% 0.8A 1276AS-H-100M=P2
L1
1
0.1uF / 16V
C1
1
0.1uF / 6.3V
C2
1
4.7uF / 25V
C3
7
1uF / 25V
C4, C5, C6, C7, C8, C9, C10
2
6pF
C11, C12
2
1uF
C13, C15
2
0.1uF
C14, C16
1
0.47R
R1
1
1
R2
1
10k
R3
1
100k
R4

DeathClock design files

The KiCad project lives in the EmileBV/DeathClock repository on GitHub; these links point at the commit this page was built from.

DeathClock: common questions

What microcontroller does the DeathClock use?

The DeathClock is built around the STM32L010F4P6, from the STM32 family.

How big is the DeathClock PCB?

The DeathClock measures 37.2 × 31.2 mm, has 2 copper layers and is 1 mm thick.

How many components are on the DeathClock?

31 components, from 20 distinct parts. The full bill of materials is listed on this page.

Where can I download the DeathClock design files?

From the EmileBV/DeathClock repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.

Can I use the DeathClock design in my own project?

The repository has no license, so all rights stay with EmileBV. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the DeathClock without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.

Similar boards