UAV-PHMC

Evans-Kwashie·UAV-PHMC·hardware/hardware.kicad_pcb

UAV-PHMC PCB layout, top view — open source STM32 board by Evans-Kwashie

About the UAV-PHMC PCB

UAV-PHMC is an open source STM32 PCB design by Evans-Kwashie, published on GitHub under the CERN-OHL-S-2.0 license. It is a 4-layer board measuring 47 × 39.5 mm, with 44 components from 25 distinct parts.

Its main chip is the STM32G071KBUXN, from the STM32 family. Other key parts include the TPS562202S and INA226. By type, the board carries 17 capacitors, 11 resistors, 4 ICs, 3 connectors, 3 diodes and 2 inductors.

It belongs with the power & battery designs in this gallery.

From the project

Four-layer STM32G071 payload health and management controller PCB for a small 2S UAV: dual buck rails, INA226 voltage/current monitoring, UART, I2C and SWD debug.

UAV-PHMC is an embedded hardware project: a custom four-layer printed circuit board (PCB) for power management, health monitoring and payload interfacing on a small UAV.

The board is designed to be light and to run from a 2S battery pack. It was modelled around the Ornadyne O1, a crow-shaped, propeller-free flapping-wing reconnaissance drone. This is an independent design and is not affiliated with Ornadyne.

UAV-PHMC, from the project README
From the project README

Main components on the UAV-PHMC

TPS562202SSTM32G071KBUXNINA226

UAV-PHMC bill of materials (BOM)

44 components, 25 distinct parts — part numbers from the project's BOM.

QtyPartRefs
2
TPS562202S
U1, U2
1
STM32G071KBUXN
STM32G071KBUxN
U3
1
INA226
U4
1
AO3401A
Q1
1
JST-PH
J1
1
COMPANION
J3
1
CAM PWR
J4
1
Polyfuse
F1
1
0.1
R_Shunt1
1
SW_Push
SW1
1
SMAJ10A
D1
1
STATUS_G
D2
1
ERROR_R
D3
1
3.3UH
3.3uH
L1
1
4.7UH
4.7uH
L2
1
47UF
47uF
C1
4
10UF
10uF
C2, C3, C8, C9
7
0.1UF
0.1uF
C4, C5, C10, C11, C14, C16, C17
4
22UF
22uF
C6, C7, C12, C13
1
4.7UF
4.7uF
C15
Show 5 more
QtyPartRefs
1
30.9K
30.9k
R1
5
10K
10k
R2, R3, R5, R6, R9
1
52.3K
52.3k
R4
2
4.7K
4.7k
R7, R8
2
470
R10, R11

UAV-PHMC design files

The KiCad project lives in the Evans-Kwashie/UAV-PHMC repository on GitHub; these links point at the commit this page was built from.

UAV-PHMC: common questions

What microcontroller does the UAV-PHMC use?

The UAV-PHMC is built around the STM32G071KBUXN, from the STM32 family.

How big is the UAV-PHMC PCB?

The UAV-PHMC measures 47 × 39.5 mm, has 4 copper layers and is 1.6 mm thick.

How many components are on the UAV-PHMC?

44 components, from 25 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the UAV-PHMC design files?

From the Evans-Kwashie/UAV-PHMC repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the UAV-PHMC design in my own project?

Yes, under the terms of its CERN-OHL-S-2.0 license, which Evans-Kwashie chose for the repository.

Can I test firmware for the UAV-PHMC without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.

Similar boards