Homebrewkeyboard
gfoot·homebrewkeyboard·keyboard_vero2/keyboard_vero2.kicad_pcb
About the Homebrewkeyboard PCB
Homebrewkeyboard is an open source PCB design by gfoot, published on GitHub under the Unlicense license. It is a 1-layer board measuring 162.6 × 99.1 mm, with 85 components from 7 distinct parts.
Other key parts include the 74LS138 and 74LS374. By type, the board carries 64 switches, 8 diodes, 8 resistors, 2 ICs and 1 connector.
It belongs with the keyboards designs in this gallery.
From the project
Schematics, board layouts, and code for adding a homebrew keyboard to your electronics projects
Schematics, board layouts, and code for adding a homebrew keyboard to your electronics projects
This one uses a parallel interface, ideal for connecting directly to the address and data bus of something like a 6502.
I also have one with a serial interface, more tailored for Arduino - let me know if you're interested and I'll publish it as a separate project.
8x resistor, 10k or thereabouts 8x diode, e.g. 1N4007 66x 4-pin push-switch with 5.08mmx5.08mm (0.2") pin pitch 1x 74LS138 address decoder 1x 74LS374 8-bit latch/register with tri-state outputs 1x 15-pin header for connecting wires…

Main components on the Homebrewkeyboard
Homebrewkeyboard bill of materials (BOM)
85 components, 7 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | 74LS138 | DIP-16_W7.62mm | U1 |
| 1 | 74LS374 | DIP-20_W7.62mm | U2 |
| 1 | CONN_01X15_MALE Conn_01x15_Male | PinHeader_1x15_P2.54mm_Horizontal | J1 |
| 64 | SW_PUSH_45DEG SW_Push_45deg | SW_PUSH_6mm | SW0, SW1, SW2, SW3, SW4, SW5, SW6, SW7 +56 |
| 2 | SW_PUSH_45DEG SW_Push_45deg | SW_PUSH_6mm | SWX1, SWX3 |
| 8 | 1K | D_DO-35_SOD27_P7.62mm_Horizontal | D1, D2, D3, D4, D5, D6, D7, D8 |
| 8 | 10K | R_Axial_DIN0204_L3.6mm_D1.6mm_P7.62mm_Horizontal | R1, R2, R3, R4, R5, R6, R7, R8 |
Homebrewkeyboard design files
The KiCad project lives in the gfoot/homebrewkeyboard repository on GitHub; these links point at the commit this page was built from.
Homebrewkeyboard: common questions
How big is the Homebrewkeyboard PCB?
The Homebrewkeyboard measures 162.6 × 99.1 mm, has 1 copper layer and is 1.6 mm thick.
How many components are on the Homebrewkeyboard?
85 components, from 7 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Homebrewkeyboard design files?
From the gfoot/homebrewkeyboard repository on GitHub, which has the KiCad layout and the BOM; the links under Design files point to each one.
Can I use the Homebrewkeyboard design in my own project?
Yes, under the terms of its Unlicense license, which gfoot chose for the repository.