Glade scj-225-cotroller
GregorHorvatH·glade-scj-225-cotroller·hardware/glade-controller.kicad_pcb
About the Glade scj-225-cotroller PCB
Glade scj-225-cotroller is an open source AVR/Arduino PCB design by GregorHorvatH, published on GitHub under the MIT license. It is a 2-layer board measuring 32 × 24 mm, with 16 components from 12 distinct parts.
Its main chip is the ATTINY24A, from the AVR/Arduino family. By type, the board carries 4 transistors, 3 capacitors, 2 modules, 2 battery holders, 2 switches and 2 resistors.
It belongs with the power & battery designs in this gallery.
From the project
Glade SCJ-225 programmable controller
A drop-in replacement controller board for the Glade SCJ-225 automatic air freshener. It replaces the original electronics, drives the little motor that presses the can, and adds a simple mode switch:
The push button SW1 sprays immediately in any mode except OFF and restarts the countdown. One spray cycle is 0.33 s of motor in one direction, 0.2 s pause, then 0.7 s in the reverse direction (timings taken from a video of the original board).

Main components on the Glade scj-225-cotroller
Glade scj-225-cotroller bill of materials (BOM)
16 components, 12 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ATTINY24A ATtiny24A-SSU | SOIC-14_3.9x8.7mm_P1.27mm | U1 |
| 1 | Motor+ | WirePad_D1.7_Drill0.9 | M1 |
| 1 | Motor- | WirePad_D1.7_Drill0.9 | M2 |
| 2 | AO3401A | SOT-23 | Q1, Q3 |
| 2 | AO3400A | SOT-23 | Q2, Q4 |
| 1 | Bat+ | BatContact_Slot_1x3_Glade | BT1 |
| 1 | Bat- | BatContact_Slot_1x3_Glade | BT2 |
| 1 | TACTA-64N | SW_Tact_RA_Ninigi_TACTA-64N | SW1 |
| 1 | OS103011MS8QP1 | SW_Slide_SP3T_CK_OS103011MS8QP1 | SW2 |
| 1 | 22uF | C_0805_2012Metric | C1 |
| 2 | 100nF | C_0603_1608Metric | C2, C3 |
| 2 | 100k | R_0603_1608Metric | R1, R2 |
Glade scj-225-cotroller design files
The KiCad project lives in the GregorHorvatH/glade-scj-225-cotroller repository on GitHub; these links point at the commit this page was built from.
Glade scj-225-cotroller: common questions
What microcontroller does the Glade scj-225-cotroller use?
The Glade scj-225-cotroller is built around the ATTINY24A, from the AVR/Arduino family.
How big is the Glade scj-225-cotroller PCB?
The Glade scj-225-cotroller measures 32 × 24 mm, has 2 copper layers and is 1 mm thick.
How many components are on the Glade scj-225-cotroller?
16 components, from 12 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Glade scj-225-cotroller design files?
From the GregorHorvatH/glade-scj-225-cotroller repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Glade scj-225-cotroller design in my own project?
Yes, under the terms of its MIT license, which GregorHorvatH chose for the repository.
Can I test firmware for the Glade scj-225-cotroller without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.
Similar boards
AVR/Arduino
Magspoof
samyk
35 × 29 mm11 parts2LNo license4.2kAVR/Arduino
Redox keyboard
mattdibi
162.2 × 126.5 mm77 parts2LMIT2.0kAVR/Arduino
Labrador
espotek-org
36.8 × 34.7 mm75 parts2LNo license1.2kAVR/Arduino
V4
stuartpittaway
30 × 50 mm38 parts2LCC-BY-NC-4.01.1kAVR/Arduino
ModuleV450
stuartpittaway
30 × 61.4 mm39 parts2LCC-BY-NC-4.01.1kAVR/Arduino
Discipline
coseyfannitutti
304.9 × 122.8 mm170 parts2LCC-BY-NC-4.01.0k