Eagle to kicad qwiic button
haiha-ux·eagle-to-kicad-qwiic-button·kicad/Qwiic_Button.kicad_pcb
About the Eagle to kicad qwiic button PCB
Eagle to kicad qwiic button is an open source AVR/Arduino PCB design by haiha-ux, published on GitHub under the CC-BY-SA-4.0 license. It is a 2-layer board measuring 25.4 × 25.4 mm, with 22 components from 15 distinct parts.
Its main chip is the U4, from the AVR/Arduino family. By type, the board carries 5 connectors, 5 jumpers, 5 resistors, 1 IC, 1 switch and 1 diode.
From the project
Eagle 9 to KiCad 10 conversion of the open-source SparkFun Qwiic Button, with netlist and copper equivalence checks (CC BY-SA 4.0)
Owner: Ha Phan Thanh Hai (GitHub haiha-ux). This repository converts an open-source Eagle 9.5.2 design, the SparkFun Qwiic Button (red LED version), to a KiCad 10 project. The goal is the usual Eagle-to-KiCad migration job: a KiCad schematic and board that open cleanly, pass ERC and DRC with schematic parity, use a project library, and provably describe the same circuit and the same copper as the original.

Main components on the Eagle to kicad qwiic button
Eagle to kicad qwiic button bill of materials (BOM)
22 components, 15 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | U4 | SO14 | U4 |
| 1 | J1 | 1X04_NO_SILK | J1 |
| 2 | QWIIC_RIGHT_ANGLE | JST04_1MM_RA | J2, J3 |
| 1 | J5 | 1X01_NO_SILK | J5 |
| 1 | ISP | 2X3_TEST_POINTS | J7 |
| 2 | #4 screw | STAND-OFF | H1, H2 |
| 1 | SolderJumper | SMT-JUMPER_2_NC_TRACE_SILK | INT0 |
| 4 | SolderJumper | SMT-JUMPER_2_NO_NO-SILK | JP1, JP4, JP5, JP7 |
| 1 | SolderJumper | SMT-JUMPER_3_2-NC_TRACE_SILK | JP3 |
| 1 | Button | TACTILE_SWITCH_LED_PTH_12MM | S1 |
| 1 | RED | LED-0603 | D1 |
| 1 | 0.1uF | 0603 | C2 |
| 2 | 2.2k | 0603 | R1, R2 |
| 2 | 10k | 0603 | R3, R11 |
| 1 | 1k | 0603 | R4 |
Eagle to kicad qwiic button design files
The KiCad project lives in the haiha-ux/eagle-to-kicad-qwiic-button repository on GitHub; these links point at the commit this page was built from.
- Layoutkicad/Qwiic_Button.kicad_pcb
- Schematickicad/Qwiic_Button.kicad_sch
Eagle to kicad qwiic button: common questions
What microcontroller does the Eagle to kicad qwiic button use?
The Eagle to kicad qwiic button is built around the U4, from the AVR/Arduino family.
How big is the Eagle to kicad qwiic button PCB?
The Eagle to kicad qwiic button measures 25.4 × 25.4 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Eagle to kicad qwiic button?
22 components, from 15 distinct parts. The full bill of materials is listed on this page.
Where can I download the Eagle to kicad qwiic button design files?
From the haiha-ux/eagle-to-kicad-qwiic-button repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Eagle to kicad qwiic button design in my own project?
Yes, under the terms of its CC-BY-SA-4.0 license, which haiha-ux chose for the repository.
Can I test firmware for the Eagle to kicad qwiic button without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.
Similar boards
AVR/Arduino
Magspoof
samyk
35 × 29 mm11 parts2LNo license4.2kAVR/Arduino
Redox keyboard
mattdibi
162.2 × 126.5 mm77 parts2LMIT2.0kAVR/Arduino
Labrador
espotek-org
36.8 × 34.7 mm75 parts2LNo license1.2kAVR/Arduino
ModuleV450
stuartpittaway
30 × 61.4 mm39 parts2LCC-BY-NC-4.01.1kAVR/Arduino
V4
stuartpittaway
30 × 50 mm38 parts2LCC-BY-NC-4.01.1kAVR/Arduino
Discipline
coseyfannitutti
304.9 × 122.8 mm170 parts2LCC-BY-NC-4.01.0k