Binary clock

henry781·binary-clock·hardware/binary_clock.kicad_pcb

Binary clock PCB layout, top view — open source AVR/Arduino board by henry781

About the Binary clock PCB

Binary clock is an open source AVR/Arduino PCB design by henry781, published on GitHub under the MIT license. It is a 2-layer board measuring 180 × 180 mm, with 76 components from 24 distinct parts.

Its main chip is the ATmega328P-P, from the AVR/Arduino family. Other key parts include the CD4040BE and SN74HC245N. By type, the board carries 18 LEDs, 6 ICs, 3 switches, 2 capacitors and 1 crystal.

From the project

KiCad 10 project of the clock, board revision B.

KiCad 10 project of the clock, board revision B.

Round board, Ø 180 mm, two layers. All parts go on the front; they are through-hole parts, except the DCF77 module. The circuit is described in docs/hardware.md; fabrication files and assembly are covered in docs/assembly.md.

Main components on the Binary clock

CD4040BESN74HC245N

Binary clock bill of materials (BOM)

76 components, 24 distinct parts — part numbers from the project's BOM.

QtyPartRefs
3
CD4040BE
4040
Texas Instruments
U3, U4, U5
3
SN74HC245N
74HC245
Texas Instruments
U11, U12, U13
1
DT-38
32.768 kHz
KDS
Y1
11
100nF
C_AREF1, C_DCF_VCC1, C_DEC_MCU_AVCC1, C_DEC_MCU_VCC1, C_DEC_U3, C_DEC_U4, C_DEC_U5, C_DEC_U11 +3
1
100uF 16V
C_BULK1
2
1uF
C_LDO_IN1, C_LDO_OUT1
1
1N5817
D_TERM1
1
UART Header
J_DBG1
1
ISP Header
J_ISP1
1
5V IN (screw terminal)
J_PWR2
1
600R @ 100MHz
L_AVCC1
1
DCF-3850M-800
MOD_DCF1
1
2N3904
Q_DCF1
4
10K
R_DCF_C1, R_DCF_OUT1, R_OE1, R_RST1
1
100
R_DCF_VCC1
12
220
R_LED_B1, R_LED_B2, R_LED_B3, R_LED_B4, R_LED_B5, R_LED_B6, R_LED_G1, R_LED_G2 +4
5
330
R_LED_R1, R_LED_R2, R_LED_R3, R_LED_R4, R_LED_R5
1
470k
R_PT1
3
SW_Push
C&K
SW1, SW2, SW3
1
MCP1700-3302E
U_LDO1
Show 4 more
QtyPartRefs
1
ATmega328P-P
U_MCU1
17
LED
D_B1, D_B2, D_B3, D_B4, D_B5, D_B6, D_G1, D_G2 +9
1
TEPT5700
Q_PT1
2
CC-15/100
15pF
SR Passives
C1, C2

Binary clock design files

The KiCad project lives in the henry781/binary-clock repository on GitHub; these links point at the commit this page was built from.

Binary clock: common questions

What microcontroller does the Binary clock use?

The Binary clock is built around the ATmega328P-P, from the AVR/Arduino family.

How big is the Binary clock PCB?

The Binary clock measures 180 × 180 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Binary clock?

76 components, from 24 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the Binary clock design files?

From the henry781/binary-clock repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the Binary clock design in my own project?

Yes, under the terms of its MIT license, which henry781 chose for the repository.

Can I test firmware for the Binary clock without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.

Similar boards