Custom-Microcontroller
j-exinia·Custom-Microcontroller·ExOneMicrorocessor/ExOneMicrorocessor.kicad_pcb
About the Custom-Microcontroller PCB
Custom-Microcontroller is an open source STM32 PCB design by j-exinia, published on GitHub. It is a 2-layer board measuring 33.5 × 62.7 mm, with 40 components from 25 distinct parts.
Its main chip is the STM32G041C8T6, from the STM32 family. Other key parts include the FT230XS and TPS77733DR. By type, the board carries 19 capacitors, 7 resistors, 6 connectors, 3 ICs, 2 crystals and 1 fuse.
From the project
1st attempt at creating a Micro controller

Main components on the Custom-Microcontroller
Custom-Microcontroller bill of materials (BOM)
40 components, 25 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | STM32G041C8T6 | STM32G041C8 | IC1 |
| 1 | FT230XS | FT230XS | IC2 |
| 1 | TPS77733DR | TPS77733 | U1 |
| 1 | 32.768 kHz | Crystal_SMD_3215-2Pin_3.2x1.5mm | Y1 |
| 1 | 8 MHz | Crystal_SMD_HC49-SD_HandSoldering | Y2 |
| 1 | UJ2-MBH-3-SMT | UJ2-MBH-SMT | J1 |
| 1 | Conn_01x02 | JST_EH_B2B-EH-A_1x02_P2.50mm_Vertical | J2 |
| 1 | 02x03 Header | PinHeader_2x03_P2.54mm_Vertical | J3 |
| 2 | Conn_01x17 | PinHeader_1x17_P2.54mm_Vertical | J4, J5 |
| 1 | Conn_01x02 | PinHeader_1x02_P2.54mm_Vertical | J6 |
| 1 | 750mA | Fuse_1206_3216Metric_Pad1.42x1.75mm_HandSolder | F1 |
| 1 | SW_Push | PTS636SM25SMTRLFS | SW1 |
| 1 | D | D_SOD-123 | D1 |
| 4 | 4.7 uF | C_0603_1608Metric_Pad1.05x0.95mm_HandSolder | C1, C14, C15, C18 |
| 6 | 0.1 uF | C_0603_1608Metric_Pad1.05x0.95mm_HandSolder | C2, C3, C12, C13, C16, C19 |
| 1 | 1 uF | C_0603_1608Metric_Pad1.05x0.95mm_HandSolder | C4 |
| 2 | 12.5 pF | C_0603_1608Metric_Pad1.05x0.95mm_HandSolder | C5, C6 |
| 2 | 20 pF | C_0603_1608Metric_Pad1.05x0.95mm_HandSolder | C7, C8 |
| 1 | 0.01 uF | C_0603_1608Metric_Pad1.05x0.95mm_HandSolder | C9 |
| 2 | 47 pF | C_0603_1608Metric_Pad1.05x0.95mm_HandSolder | C10, C11 |
Show 5 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | 10 uF | C_0603_1608Metric_Pad1.05x0.95mm_HandSolder | C17 |
| 2 | 27Ω | R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R1, R2 |
| 2 | 100Ω | R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R3, R4 |
| 2 | 10kΩ | R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R5, R6 |
| 1 | 250kΩ | R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R7 |
Custom-Microcontroller design files
The KiCad project lives in the j-exinia/Custom-Microcontroller repository on GitHub; these links point at the commit this page was built from.
Custom-Microcontroller: common questions
What microcontroller does the Custom-Microcontroller use?
The Custom-Microcontroller is built around the STM32G041C8T6, from the STM32 family.
How big is the Custom-Microcontroller PCB?
The Custom-Microcontroller measures 33.5 × 62.7 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Custom-Microcontroller?
40 components, from 25 distinct parts. The full bill of materials is listed on this page.
Where can I download the Custom-Microcontroller design files?
From the j-exinia/Custom-Microcontroller repository on GitHub, which has the KiCad layout; the links under Design files point to each one.
Can I use the Custom-Microcontroller design in my own project?
The repository has no license, so all rights stay with j-exinia. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Custom-Microcontroller without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.
Similar boards
STM32
LumenPnP Motherboard
opulo-inc
149 × 95 mm296 parts4LCC-BY-SA-4.03.7kSTM32
Type g
google
169 × 30 mm24 parts2LApache-2.02.9kSTM32
Main panel
google
234 × 84 mm26 parts4LApache-2.02.9kSTM32
Base
google
52.3 × 52.3 mm36 parts2LApache-2.02.9kSTM32
Type a
google
150 × 30 mm14 parts2LApache-2.02.9kSTM32
Type c
google
188 × 30 mm17 parts2LApache-2.02.9k