Brushed DC Motor Driver
JaybeJaybeNot·Pusher1.0·Electrical Design/Brushed_DC_Motor_Driver/Brushed_DC_Motor_Driver.kicad_pcb
About the Brushed DC Motor Driver PCB
Brushed DC Motor Driver is an open source STM32 PCB design by JaybeJaybeNot, published on GitHub. It is a 4-layer board measuring 80.8 × 41.2 mm, with 29 components from 19 distinct parts.
Its main chip is the CONN-TH_L53.3-W22.9_STM32F103C8T6-CARD, from the STM32 family. By type, the board carries 7 resistors, 6 capacitors, 4 transistors, 4 connectors, 3 ICs and 1 diode.
It belongs with the robotics & motion designs in this gallery.
From the project
Affiliation: Fallout, Hackclub (officially funded, $230)
Affiliation: Fallout, Hackclub (officially funded, $230)
Sanity Checked by a friend, a CS Graduate from UofM working in robotics.
Pusher is a 4 Degree of Freedom wearable robotic arm based on the anatomical structure of the human arm, with a maximum reach of approximately 0.65 meters and a weight of 5 kilograms. It is designed for modularity, aiming to serve as an affordable, general-purpose research platform for Human-Computer Interfacing, such as studies involving EMG, EEG, and Computer Vision, to assist in the control of supernumerary arms. As such, this project is intended for both…
Brushed DC Motor Driver bill of materials (BOM)
29 components, 19 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 2 | ~ TI(德州仪器) | VQFN-24_L4.0-W4.0-P0.50-BL-EP2.5 | U1, U3 |
| 1 | ~ 立创开发板 | CONN-TH_L53.3-W22.9_STM32F103C8T6-CARD | U2 |
| 4 | ~ TI(德州仪器) | VSON-CLIP-8_L5.0-W6.0-P1.27-BL | Q1, Q2, Q3, Q4 |
| 1 | CONN_01X02_PIN Conn_01x02_Pin | Samtec_HPM-02-01-x-S_Straight_1x02_Pitch5.08mm | J1 |
| 1 | CONN_01X03_PIN Conn_01x03_Pin | Samtec_HPM-03-01-x-S_Straight_1x03_Pitch5.08mm | J3 |
| 1 | A/B Position Feedback | Samtec_HPM-02-01-x-S_Straight_1x02_Pitch5.08mm | J4 |
| 1 | PWM | Samtec_HPM-02-01-x-S_Straight_1x02_Pitch5.08mm | J5 |
| 3 | TestPoint | TestPoint_Loop_D2.50mm_Drill1.0mm_LowProfile | 3v3, 24v1, gnd1 |
| 1 | 10kΩ BOURNS | RES-ADJ-TH_3362P | VR1 |
| 1 | LED | C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | D1 |
| 2 | 0.1 uF | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C1, C4 |
| 1 | 10 uF | CP_Elec_5x5.4 | C2 |
| 1 | 1 uF, 16V | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C3 |
| 2 | 1 uF, 6.3v | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C5, C6 |
| 1 | 2k R | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | R1 |
| 1 | 3.3KR 3.3kR | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | R2 |
| 1 | 68k R | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | R3 |
| 1 | 0.03 R | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | R4 |
| 3 | 10k R | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | R5, R6, R7 |
Brushed DC Motor Driver design files
The KiCad project lives in the JaybeJaybeNot/Pusher1.0 repository on GitHub; these links point at the commit this page was built from.
Brushed DC Motor Driver: common questions
What microcontroller does the Brushed DC Motor Driver use?
The Brushed DC Motor Driver is built around the CONN-TH_L53.3-W22.9_STM32F103C8T6-CARD, from the STM32 family.
How big is the Brushed DC Motor Driver PCB?
The Brushed DC Motor Driver measures 80.8 × 41.2 mm, has 4 copper layers and is 1.6 mm thick.
How many components are on the Brushed DC Motor Driver?
29 components, from 19 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Brushed DC Motor Driver design files?
From the JaybeJaybeNot/Pusher1.0 repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Brushed DC Motor Driver design in my own project?
The repository has no license, so all rights stay with JaybeJaybeNot. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Brushed DC Motor Driver without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.
More boards in Pusher1.0
Similar boards
STM32
LumenPnP Motherboard
opulo-inc
149 × 95 mm296 parts4LCC-BY-SA-4.03.7kSTM32
Type g
google
169 × 30 mm24 parts2LApache-2.02.9kSTM32
Main panel
google
234 × 84 mm26 parts4LApache-2.02.9kSTM32
Base
google
52.3 × 52.3 mm36 parts2LApache-2.02.9kSTM32
Type a
google
150 × 30 mm14 parts2LApache-2.02.9kSTM32
Type c
google
188 × 30 mm17 parts2LApache-2.02.9k