Joystick Kicad 9.0
JaybeJaybeNot·Pusher1.0·Electrical Design/Joystick_Kicad_9.0/Joystick_Kicad_9.0.kicad_pcb
About the Joystick Kicad 9.0 PCB
Joystick Kicad 9.0 is an open source ESP32 PCB design by JaybeJaybeNot, published on GitHub. It is a 2-layer board measuring 63.7 × 73.8 mm, with 14 components from 11 distinct parts.
Its main chip is the DIP-40_L20.32-W51.66-P2.54-LS15.24, from the ESP32 family. By type, the board carries 5 connectors, 5 resistors, 2 switches, 1 IC and 1 diode.
From the project
Affiliation: Fallout, Hackclub (officially funded, $230)
Affiliation: Fallout, Hackclub (officially funded, $230)
Sanity Checked by a friend, a CS Graduate from UofM working in robotics.
Pusher is a 4 Degree of Freedom wearable robotic arm based on the anatomical structure of the human arm, with a maximum reach of approximately 0.65 meters and a weight of 5 kilograms. It is designed for modularity, aiming to serve as an affordable, general-purpose research platform for Human-Computer Interfacing, such as studies involving EMG, EEG, and Computer Vision, to assist in the control of supernumerary arms. As such, this project is intended for both…
Joystick Kicad 9.0 bill of materials (BOM)
14 components, 11 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ~ 立创开发板 | DIP-40_L20.32-W51.66-P2.54-LS15.24 | U1 |
| 1 | ~ JST | CONN-TH_B2B-PH-K-S | CN1 |
| 1 | CONN_01X14_PIN Conn_01x14_Pin | Samtec_HPM-14-01-x-S_Straight_1x14_Pitch5.08mm | J1 |
| 1 | CONN_01X08_PIN Conn_01x08_Pin | Samtec_HPM-08-01-x-S_Straight_1x08_Pitch5.08mm | J2 |
| 1 | CONN_01X02_PIN Conn_01x02_Pin | Samtec_HPM-02-01-x-S_Straight_1x02_Pitch5.08mm | J3 |
| 1 | TYPE-C_16PIN_2MD__073_ | SHOUHAN_TYPE-C_16PIN_2MD__073_ | J4 |
| 2 | ~ ALPSALPINE(阿尔卑斯阿尔派) | SW-TH_RKJXV1224005 | SW1, SW2 |
| 1 | LED | C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | D1 |
| 2 | R | C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | R1, R2 |
| 1 | <1k | C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | R3 |
| 2 | 5.1k R | R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R10, R11 |
Joystick Kicad 9.0 design files
The KiCad project lives in the JaybeJaybeNot/Pusher1.0 repository on GitHub; these links point at the commit this page was built from.
Joystick Kicad 9.0: common questions
What microcontroller does the Joystick Kicad 9.0 use?
The Joystick Kicad 9.0 is built around the DIP-40_L20.32-W51.66-P2.54-LS15.24, from the ESP32 family.
How big is the Joystick Kicad 9.0 PCB?
The Joystick Kicad 9.0 measures 63.7 × 73.8 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Joystick Kicad 9.0?
14 components, from 11 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Joystick Kicad 9.0 design files?
From the JaybeJaybeNot/Pusher1.0 repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Joystick Kicad 9.0 design in my own project?
The repository has no license, so all rights stay with JaybeJaybeNot. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Joystick Kicad 9.0 without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
More boards in Pusher1.0
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k