STM32F103C8T6-Board
John-Coding-c·STM32F103C8T6-Board
About the STM32F103C8T6-Board
STM32F103C8T6-Board is an open source STM32 PCB design by John-Coding-c, published on GitHub under the MIT license. It is a 2-layer board measuring 41 × 31 mm, with 28 components from 16 distinct parts.
Its main chip is the STM32F103C8T6, from the STM32 family. Other key parts include the AMS1117-3.3. By type, the board carries 13 capacitors, 5 resistors, 4 connectors, 2 ICs, 1 crystal and 1 switch.
From the project
A small custom PCB built around the STM32F103C8T6 (ARM Cortex-M3, 72 MHz) microcontroller.
A small custom PCB built around the STM32F103C8T6 (ARM Cortex-M3, 72 MHz) microcontroller.
- MCU: STM32F103C8T6 (LQFP-48, 64 KB Flash, 20 KB RAM) - Power: USB 5 V input → AMS1117-3.3 LDO → 3.3 V rail, with a power LED (D1) - Clock: 16 MHz crystal (Y1) with load capacitors - USB: USB Micro-B connector (J4) with 1.5 kΩ pull-up on D+ - Boot: SPDT switch (SW1) to select boot mode via BOOT0, with a 10 kΩ resistor (R4) on BOOT0 - Debug: 4-pin SWD header (SWDIO, SWCLK, 3.3 V, GND) - Serial: 4-pin USART1 header (TX/RX, 3.3 V, GND) - I2C: 4-pin I2C2 header (SCL/SDA with 1.5 kΩ pull-ups, 3.3 V, GND) -…

Main components on the STM32F103C8T6-Board
STM32F103C8T6-Board bill of materials (BOM)
28 components, 16 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | AMS1117-3.3 | SOT-223-3_TabPin2 | U1 |
| 1 | STM32F103C8T6 | LQFP-48_7x7mm_P0.5mm | U2 |
| 1 | 16MHZ 16MHz | Crystal_SMD_3225-4Pin_3.2x2.5mm | Y1 |
| 3 | CONN_01X04_MALE Conn_01x04_Male | PinHeader_1x04_P2.54mm_Vertical | J1, J2, J3 |
| 1 | USB_B_Micro | USB_Micro-B_Wuerth_629105150521 | J4 |
| 1 | SW_SPDT | SW_SPDT_PCM12 | SW1 |
| 1 | RED | LED_0603_1608Metric | D1 |
| 1 | 120R | L_0603_1608Metric | FB1 |
| 2 | 22U 22u | C_0805_2012Metric | C1, C2 |
| 1 | 10U 10u | C_0603_1608Metric | C3 |
| 5 | 100N 100n | C_0402_1005Metric | C4, C6, C7, C9, C10 |
| 2 | 10P 10p | C_0402_1005Metric | C5, C8 |
| 1 | 10N 10n | C_0402_1005Metric | C11 |
| 2 | 1u | C_0402_1005Metric | C12, C13 |
| 4 | 1K5 1k5 | R_0402_1005Metric | R1, R2, R3, R5 |
| 1 | 10K 10k | R_0402_1005Metric | R4 |
STM32F103C8T6-Board design files
The KiCad project lives in the John-Coding-c/STM32F103C8T6-Board repository on GitHub; these links point at the commit this page was built from.
- LayoutSTM32.kicad_pcb
- SchematicSTM32.kicad_sch
- BOMmanufacture/STM32-BOM.csv
STM32F103C8T6-Board: common questions
What microcontroller does the STM32F103C8T6-Board use?
The STM32F103C8T6-Board is built around the STM32F103C8T6, from the STM32 family.
How big is the STM32F103C8T6-Board?
The STM32F103C8T6-Board measures 41 × 31 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the STM32F103C8T6-Board?
28 components, from 16 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the STM32F103C8T6-Board design files?
From the John-Coding-c/STM32F103C8T6-Board repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the STM32F103C8T6-Board design in my own project?
Yes, under the terms of its MIT license, which John-Coding-c chose for the repository.
Can I test firmware for the STM32F103C8T6-Board without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.
Similar boards
STM32
LumenPnP Motherboard
opulo-inc
149 × 95 mm296 parts4LCC-BY-SA-4.03.7kSTM32
Type g
google
169 × 30 mm24 parts2LApache-2.02.9kSTM32
Main panel
google
234 × 84 mm26 parts4LApache-2.02.9kSTM32
Base
google
52.3 × 52.3 mm36 parts2LApache-2.02.9kSTM32
Type a
google
150 × 30 mm14 parts2LApache-2.02.9kSTM32
Type c
google
188 × 30 mm17 parts2LApache-2.02.9k