Nexa-Board
KarlVaello·Nexa-Board·Nexa/Nexa.kicad_pcb
About the Nexa-Board
Nexa-Board is an open source STM32 PCB design by KarlVaello, published on GitHub under the GPL-3.0 license. It is a 2-layer board measuring 90 × 60 mm, with 72 components from 33 distinct parts.
Its main chip is the STM32F103C8, from the STM32 family. Other key parts include the LM1117-5.0, LM1117-3.3 and MAX485E. By type, the board carries 24 resistors, 19 connectors, 11 capacitors, 6 diodes, 5 ICs and 2 crystals.
From the project
Nexa is a Open Source Hardware board based on STM32f103 with a full duplex rs-485 interface
In need of satisfying the ISO 15765-2 the board will receive hardware changes.
ISO 15765-2, or ISO-TP (Transport Layer), is an international standard for sending data packets over a CAN-Bus. The protocol allows for the transport of messages that exceed the eight byte maximum payload of CAN frames. ISO-TP segments longer messages into multiple frames, adding metadata that allows the interpretation of individual frames and reassembly into a complete message packet by the recipient. It can carry up to 4095 bytes of payload per message packet.

Main components on the Nexa-Board
Nexa-Board bill of materials (BOM)
72 components, 33 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | STM32F103C8 | LQFP-48_7x7mm_Pitch0.5mm | U1 |
| 1 | LM1117-5.0 | SOT-223 | U2 |
| 1 | LM1117-3.3 | SOT-223 | U3 |
| 2 | MAX485E | SOIC-8_3.9x4.9mm_Pitch1.27mm | U4, U5 |
| 1 | Q_NMOS_GDS | TO-252-2 | Q1 |
| 1 | 8 MHz | Crystal_HC49-4H_Vertical | Y1 |
| 1 | 32.768 KHz | Crystal_SMD_SeikoEpson_MC306-4pin_8.0x3.2mm_HandSoldering | Y2 |
| 1 | Conn_01x04 | Pin_Header_Straight_1x04_Pitch2.54mm | J1 |
| 5 | Conn_01x02_Male | Pin_Header_Straight_1x02_Pitch2.54mm | J2, J9, J10, J12, J13 |
| 1 | Conn_01x04 | Molex_MiniFit-JR-5569-04A2_2x02x4.20mm_Angled | J3 |
| 1 | Conn_02x03_Odd_Even | Pin_Header_Straight_2x03_Pitch2.54mm | J4 |
| 1 | Conn_01x23 | Socket_Strip_Straight_1x23_Pitch2.54mm | J5 |
| 1 | proto_grid_15x21 | grid | J6 |
| 2 | Conn_02x02_Top_Bottom | Pin_Header_Straight_2x02_Pitch2.54mm | J7, J8 |
| 3 | Conn_01x01 | Pin_Header_Straight_1x01_Pitch2.54mm | J14, J15, J16 |
| 4 | Conn_01x01 | MountHoles_H3.2mm_D5.5 | J18, J19, J20, J21 |
| 1 | 10uF - 25V | CP_Tantalum_Case-C_EIA-6032-28_Hand | CP1 |
| 1 | 22uF - 16V | CP_Tantalum_Case-B_EIA-3528-21_Hand | CP2 |
| 1 | 22uF - 16 V | CP_Tantalum_Case-B_EIA-3528-21_Hand | CP4 |
| 1 | SW_Push | SW_PUSH_6mm_h8.5mm | SW1 |
Show 13 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 5 | LED | LED_0805_HandSoldering | D1, D2, D3, D4, D5 |
| 1 | D | D_SMB | D6 |
| 4 | 100nF | C_0603_HandSoldering | C1, C3, C4, C5 |
| 1 | 1.0uF | C_0603_HandSoldering | C2 |
| 4 | 22pF | C_0603_HandSoldering | C6, C7, C8, C9 |
| 2 | 100nF | C_0805_HandSoldering | C10, C11 |
| 10 | 10K | R_0603_HandSoldering | R1, R7, R8, R9, R10, R11, R12, R13 +2 |
| 1 | 1M | R_0603_HandSoldering | R2 |
| 4 | 120R | R_0603_HandSoldering | R3, R4, R19, R20 |
| 2 | 100K | R_0603_HandSoldering | R5, R6 |
| 4 | 20K | R_0603_HandSoldering | R15, R16, R17, R18 |
| 1 | 510R | R_0603_HandSoldering | R21 |
| 2 | 2K | R_0603_HandSoldering | R22, R24 |
Nexa-Board design files
The KiCad project lives in the KarlVaello/Nexa-Board repository on GitHub; these links point at the commit this page was built from.
- LayoutNexa/Nexa.kicad_pcb
Nexa-Board: common questions
What microcontroller does the Nexa-Board use?
The Nexa-Board is built around the STM32F103C8, from the STM32 family.
How big is the Nexa-Board?
The Nexa-Board measures 90 × 60 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Nexa-Board?
72 components, from 33 distinct parts. The full bill of materials is listed on this page.
Where can I download the Nexa-Board design files?
From the KarlVaello/Nexa-Board repository on GitHub, which has the KiCad layout; the links under Design files point to each one.
Can I use the Nexa-Board design in my own project?
Yes, under the terms of its GPL-3.0 license, which KarlVaello chose for the repository.
Can I test firmware for the Nexa-Board without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.
Similar boards
STM32
LumenPnP Motherboard
opulo-inc
149 × 95 mm296 parts4LCC-BY-SA-4.03.7kSTM32
Type g
google
169 × 30 mm24 parts2LApache-2.02.9kSTM32
Main panel
google
234 × 84 mm26 parts4LApache-2.02.9kSTM32
Base
google
52.3 × 52.3 mm36 parts2LApache-2.02.9kSTM32
Type a
google
150 × 30 mm14 parts2LApache-2.02.9kSTM32
Type c
google
188 × 30 mm17 parts2LApache-2.02.9k