87 open source boards using the MAX485E
Real designs built with the MAX485E, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
STM32
FastLOGIC
Neumi
123 × 87.5 mm181 parts4LMIT23NXP
Piccolo-4C-Black
SylvainVanIniitu
257.2 × 166.2 mm68 parts2LCC-BY-NC-4.016STM32
VehicleControlSystem
KarlVaello
85 × 60 mm66 parts2LGPL-3.014CTA control board
PySpice-org
252 × 152 mm614 parts4LNo license9ESP32
ESp32-DEVKIT-DATALOGGER
Zektopic
262.2 × 139.3 mm84 parts2LNo license7Coonix
TreeNewbeer
95 × 85 mm164 parts2LNo license4RISC-V
CCController
RainbowLabsDE
180 × 80 mm79 parts2LMIT4ESP32
Mainboard
Synthron
160 × 100 mm206 parts4LNo license3STM32
KbxBinaryClock.v4
kbx81
127 × 114.3 mm128 parts2LNo license2STM32
Nexa-Board
KarlVaello
90 × 60 mm72 parts2LGPL-3.02ESP32
Frontend
bullestock
63.6 × 49 mm52 parts2LGPL-3.02STM32
Nmea pi hat
ronangaillard
65 × 56 mm51 parts2LMIT2RP2040/RP2350
Autotracking Surgical Lamp
aeventre
56 × 79 mm41 parts2LNo license2DifferentialEncoderMaster
Wetmelon
63 × 46.5 mm31 parts4LMIT2AVR/Arduino
Arduino-MidiDmxBridge
chrisneukam
65 × 47 mm29 parts2LApache-2.02ESP32
EndevourDMX
Darbyshire64
143 × 75.5 mm17 parts2LMIT2AVR/Arduino
Weather station
z0b1
37.3 × 36.5 mm11 parts4LNo license2AVR/Arduino
Plc-4u a
semicontinuity
64 × 84 mm215 parts2LNo license1ESP32
Clean room slave
trieuhuyduc
165 × 110 mm207 parts2LNo license1ModBus-RJ45-Breakout-2
the78mole
87 × 68 mm116 parts2LTAPR-OHL-1.01STM32
GaiForgeWeb-
GaiaForge
104.9 × 78 mm81 parts2LNo license1RS485
Solderingironspb
32 × 52 mm50 parts2LNo license1KiCad-DMX-Pixel-1
vanvught
84.8 × 62.1 mm31 parts2LMIT1ESP32
TRANCE USB-DMX
Soraxem
44 × 20 mm21 parts2LCERN-OHL-P-2.01ESP32
ELISTARS
R-Mutura
102 × 86.3 mm281 parts4LNo license0STM32
STM32 IOT GATEWAY
RiddheshVeling
99 × 105 mm154 parts2LNo license0STM32
Sim multiplexer
0x178F
436 × 70 mm150 parts4LApache-2.00AVR/Arduino
ATmega328 control Board
olexsu
124 × 89.4 mm129 parts4LMIT0ESP32
Fiberboard
nguyenduchan
118 × 84 mm116 parts2LNo license0Raspberry Pi
Pwrcmder
reaktor23
138.5 × 84 mm112 parts2LMIT0ESP32
Chicken door
pavelkejik
108.1 × 67 mm85 parts2LNo license0RetroCom
SamyIOoOI
190 × 111 mm84 parts2LGPL-3.00AVR/Arduino
Home-Automation-System
0101shift
86.4 × 90.2 mm81 parts2LNo license0RP2040/RP2350
Controlbox
edwindertien
139 × 55.2 mm81 parts2LNo license0Golf-Robot-2024
ibuki-oono
68.6 × 53.3 mm75 parts2LNo license0ESP32
KleverLogger
charclo
50 × 50 mm61 parts4LNo license0
How designs wire the MAX485E
Read from the KiCad layouts of 63 open source designs, one per repository: what each pin of the MAX485E connects to, and the resistors, capacitors and other passives placed on it.
- The A pin has a series resistor on 40 of 62 designs, most often 120 Ω (then 10 Ω).
- The B pin has a series resistor on 40 of 62 designs, most often 120 Ω (then 10 Ω).
- The VCC pin has a decoupling capacitor on 36 of 62 designs, most often 100 nF (then 10 µF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| GNDpin 5 | Connected to: GND 94% | — |
| Apin 6 | Connected to: A connector 71% |
|
| Bpin 7 | Connected to: A connector 68% |
|
| VCCpin 8 | Connected to: 5V 84% |
|
4 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Modbus by multigcs, FastLOGIC by Neumi, Piccolo-4C-Black by SylvainVanIniitu and VehicleControlSystem by KarlVaello.
The MAX485E in open source designs
The gallery holds 87 open source boards using the MAX485E from 65 GitHub repositories; a typical one measures about 80 × 71.1 mm and carries around 52 components.
86% are two-layer designs, the rest use four layers or more, and 38% carry an open source license.
The most starred is Symio by multigcs.
Parts used alongside the MAX485E
Microcontrollers on boards using the MAX485E
What boards using the MAX485E are built for
MAX485E: common questions
Where can I find a MAX485E reference design?
Each of the 87 boards on this page is a real design using the MAX485E. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the MAX485E A pin?
The A pin has a series resistor on 40 of 62 designs, most often 120 Ω (then 10 Ω). Counted from the KiCad layouts of 63 open source designs using the MAX485E.
What resistor goes on the MAX485E B pin?
The B pin has a series resistor on 40 of 62 designs, most often 120 Ω (then 10 Ω). Counted from the KiCad layouts of 63 open source designs using the MAX485E.
What decoupling capacitors do designs use on the MAX485E VCC pin?
The VCC pin has a decoupling capacitor on 36 of 62 designs, most often 100 nF (then 10 µF). Counted from the KiCad layouts of 63 open source designs using the MAX485E.
What parts are used alongside the MAX485E?
The AMS1117-3.3, PC817, ESP32-WROOM-32, USBLC6-2SC6 and 74HCT04 appear in the most repositories here.
Which microcontrollers do boards using the MAX485E use?
Most are built on ESP32 (17), AVR/Arduino (17), STM32 (12) and RISC-V (6).
How big is a typical board using the MAX485E?
The median is 80 × 71.1 mm, and 86% are two-layer designs.
What is the most popular open source board using the MAX485E?
By GitHub stars, Symio by multigcs, with 91 stars.
Can I simulate one of these boards using the MAX485E before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.